Rubber bumper turn signal lenses are used in TVR’s and probably others, steel bumper lenses I have not seen on other cars. ...   03-05-2023 02:54 am

Thanks for clearing that up Bruce, I was confusing the fork and pivot. Brett ...   02-22-2023 08:19 pm

The fork pivot is different between the two if you go with part numbers, I don’t have access to the shifting forks right now and ...   02-21-2023 11:25 pm

Pretty sure it’s by the stromberg carb closest to the firewall, it’s been so long since I removed all that stuff, but that had vac ...   02-16-2023 01:49 am

Late JH’s wiring benefits from having both a GT and JH diagram. Yes later cars had the anti run on valve. Brett ...   02-15-2023 10:56 pm

Sander, I had heard that Jim had passed and always wondered what had happen to that amazing car, glad to hear that it is in ...   01-30-2023 02:26 pm

I first saw that car at the Nashville Jensen Nationals and thought it was one of the best well laid out modified Jensen’s I had ...   01-29-2023 04:33 pm

If you Google stromberg air filter ram flow Moss Motors pops up with a alternative. ...   01-20-2023 11:13 pm

1/4-20 ...   10-15-2021 02:03 pm

As Bruce states DON'T USE PAPER GASKET, if you belong to FB join Jensen-Healey and check out the "Files" section on UP TO DATE info ...   09-22-2021 02:17 pm

Bump, Getting close. ...   08-10-2021 01:56 pm

Bump ...   07-05-2021 01:41 pm

Do to all of the issues with Covid we moved the Jensen Meet from June to Sept. The new dates are Sept. 1 -5 If you ...   04-10-2021 01:38 pm

It should under normal conditions just slide in from one side or the other, no cut at all . Brett ...   11-21-2020 02:02 pm

For my 2 cents, I've seen a ton of Healey's and vapor lock on one would be a stretch.... can't hurt to try it though. If ...   11-18-2020 07:28 pm

I'm thinking that the positive crankcase ventilation that you mentioned might be a issue, if it's venting back into itself it's actually not venting. A ...   11-18-2020 02:42 pm

If you are going to have the dizzy apart don't forget to add the inner oil seal update, if you need details go to Jensen-Healey ...   11-10-2020 02:36 pm

On the engine block rear flange above the starter. ...   10-30-2020 04:15 pm

I grabbed some info on a replacement years ago, just the shock absorb-er that someone had found to fit, last year I and another member ...   08-21-2020 01:54 pm

Jag, I miss spoke in my last response, the Trunk and door locks share the same key, or are supposed to, and yes I just ...   08-06-2020 02:27 pm

Hey If you can't have a bit of fun, no one is picking on you personally,. As for the locks, the drivers side came with a ...   08-02-2020 02:46 pm

You don't need to put the top up, but if it's hot and sunny then flip your seat backs forward so that they shade the ...   07-30-2020 02:28 pm

The last thing in the world you want to do in a convertible is lock the doors, all it takes is a knife to splash ...   07-29-2020 01:52 pm

Hey Art, I went with a smaller 13" with a 2" dish, and love it. Brett ...   06-18-2020 02:17 pm

If you mean tightening the new studs into the block, ? then just double nut them and tighten down that way. Brett ...   05-01-2020 01:37 pm

Patrick, that would be the form a gasket aviation, and yes I used it ALL around the sealing surface, figured it couldn't hurt and would ...   04-30-2020 02:13 pm

Side Note, dry fit the head on the block with the gasket in place and make sure that the seal bead is not exposed, it ...   04-28-2020 02:06 pm

Yes your short one is the Standard JH 907 impeller, what Tim is showing are the vane styles, and how the 910 later version gives ...   12-19-2019 02:52 pm

The 910 needs to be cut down to match the length of the 907 impeller, make sure when yo do that there is a very ...   12-18-2019 05:05 pm

Try running a new wire to the starter, you just might have a broken one that is making intermittent contact. just run it out the ...   11-16-2019 02:25 pm

My point about 180 out was the crankshaft timing mark may line up, but if the cams are not, Then the engine is ONE revolution ...   11-03-2019 08:19 pm

Besides the crankshaft at TDC the cam shafts marks have to be aligned as well. This is what you need to do so your not out ...   11-02-2019 09:47 pm

Crank pulley AND Cam pulley's for TDC, you might 180 degrees off. ...   11-02-2019 02:23 pm

I'm just passing along some good info, so you tell me if you want it or not. ...   10-30-2019 03:53 pm

Use dielectric grease on all your connections for a trouble free future. Brett ...   10-30-2019 02:31 pm

I re-built a pump using the 910 impeller for a car under restoration and have yet to install and fire up the engine. But I ...   10-10-2019 02:42 pm

Pedal box is a major contributor to water ingress along with the seal at the top of the window and convertible top, after that it ...   10-09-2019 02:12 pm

I squeezed 110 mph out of mine, still with a bit of pedal left before I ran out of road, 130 mph out of a ...   09-09-2019 01:57 pm

My understanding is that it is not removable short of cutting it off. Brett. ...   09-02-2019 01:54 pm

On the Face book page Jensen-Healey in the files section there is a complete how to change over to the MGB turn signal, plus a ...   08-20-2019 02:25 pm