Vance, My center console was similar to yours. After being repaired and recovered, it looked wider when placed in the car. Probably due to the thickness ...   03-05-2025 11:28 pm

Well, depending on where you are there is of course, Redracer. Bruce is in Brookhaven, Georgia, US. Then Barry Spencer in Livermore California. Mike at Delta Motorsports, ...   02-26-2025 09:39 pm

I did that with the speedo cable. Cleaned it all up, lubricated it, tested it with a drill and everything seemed to work great. Until ...   12-19-2024 12:02 am

To further add to the confusion. I replaced the stock distributor and coil with the Pertronix Flamethrower II coil and electronic distributor several years ago. ...   12-14-2024 11:19 pm

This is for those of you that are not on the Jensen-Healey Facebook group or the Jensen Cars Google Group. I have made air boxes based ...   12-13-2023 12:25 am

Let's see if I can explain this clearly without a picture. Looking at the engine from the passenger side, below where the distributor mounts there is ...   12-12-2023 11:53 pm

On my 74 MK 2 engines that breather is a hose that goes from that hole to the back of the air box. Any excess ...   12-11-2023 12:22 am

I'm not sure from the photo but that could be just from use over time. Especially if they are the original ones and have worn ...   10-06-2023 12:18 am

Hopefully you took lots of measurements before removing the floor pan. When I did that to one of my cars I took lots of measurements, ...   04-19-2023 01:55 am

I'm looking if anyone has an open interior to test fit some custom dashes I have made. They fit the 2 cars here but would ...   02-26-2023 01:30 am

It's been so long but I think you push the engine compartment potion into the passenger area. The difficult part was getting the metal plate ...   02-26-2023 01:26 am

I replaced the fuse box on one of the cars with an after-market 4-fuse box with push fuses of the proper rating. Using the wiring ...   09-13-2022 01:37 am

Good news that everything is working again. I agree that tracing wires is a pain. Especially when the colors don't match. Luckily the harness is this ...   10-08-2021 06:41 pm

When I had trouble getting the flashers working properly I replaced my flasher units back in February with units from Delta. According to Jim they ...   10-08-2021 02:38 am

When I put the windows and quarter light back into one of my JHs I had everything loosen just a little so the quarter light ...   07-28-2021 12:52 am

You don't say where you are located. Check with Delta Motorsports in Phoenix or Robbins Auto Top. Also, a local auto wholesaler might be able to ...   07-25-2021 07:30 pm

Unfortunately, Mark passed away several years ago. I don't know for sure if I have the document. But I seem to remember the procedure being in ...   04-21-2021 01:34 am

Pretty much all of the hardware nuts and bolts are metric. When I needed some bolts and washers I tried Home Depot first, a local ...   03-16-2021 10:17 pm

The reason there is no fan shroud is probably because the fan shroud wouldn't fit with the electric fan was installed. Rather than try to ...   03-08-2021 11:40 pm

All I can say is Ouch! That seems to be high to me but without the itemized breakdown it's hard to say. I would do the ...   02-02-2021 11:52 pm

OK. That explains it. Fixing waves is hard to accomplish sometimes depending on how wavy the panel is. ...   01-29-2021 03:28 pm

The front hood looks like the front emblem area was worked on. Are the emblem holes welded or just covered in body filler? And it ...   01-29-2021 12:49 am

Thanks for the info. I'm going to check a wrecking yard and see what I might find there so I can see a few different ...   01-04-2021 12:45 am

I finally figured out where the rattle noise was coming from. While running the car and trying to narrow down where the noise was coming ...   12-11-2020 11:49 pm

I got under the car again to check everything one more time and the only thing that was loose was the fuel return line that ...   12-01-2020 03:22 pm

Hi Tim, I used a mold release wax that I used earlier to make a couple of pieces for something else. Those pieces popped off with ...   12-01-2020 03:11 pm

NO difference. The car is on jack stands at the moment. With the clutch depressed or not, the rattle is there. ...   11-30-2020 03:23 pm

For those following or interested here's the latest. I tried attaching photos but kept getting the error "file size too big' even though the files ...   11-30-2020 12:23 am

I working on putting a GT engine and transmission into a 1974 JH. Everything is hooked up correctly. I aligned the cams and timing marks ...   11-29-2020 11:14 pm

Thanks. With those measurements I can go locate some easier now. ...   08-30-2020 07:05 pm

Thanks for the extra info and pictures. I was in the garage working on the other parts and thought I would mock up a top ...   08-30-2020 02:27 am

Thanks for the information and suggestion. I did think of a 4" opening but decided to go more stock for now. Or what might be the ...   08-24-2020 11:23 pm

Hi Tim, Correct. The one I have here is the later square style. I made the plug to have a round end. I also made one ...   08-19-2020 01:35 am

Steve, I don't think so. From the pictures I have seen the corners are more rounded than the Lotus air boxes I have here. And there ...   08-16-2020 08:55 pm

I am making some plugs for the Lotus airbox found on the 907. When they are finished I will make the molds so I can ...   08-15-2020 08:13 pm

Thanks for the feedback. I think I found a 13" wheel on Amazon that should work. ...   07-02-2020 02:23 am

Thanks for the info guys. ...   06-18-2020 09:12 pm

I am changing from the stock steering wheel to a 13". Since they come flat and dished, those of you that have switched, what did ...   06-18-2020 12:33 am

noomg It always comes down to what you want and how much you want to pay. I haven't used the Delta seat kit but know of one ...   07-04-2019 01:25 am

Here it is in case you still haven't seen it. I made my own with some thicker gasket material using the old as a pattern . ...   10-24-2018 01:43 am