Used the black ones, that was not ok, the bottom one keeps leaking, now i have the green one, after a first test it stays ...   09-19-2021 09:01 pm

Engine is running fine now, only over 5000 rpm needs some tuning from fuel or ignition. Cold start with choke is perfect, even after Months ...   09-19-2021 08:52 pm

I did it with a car Polish machine, depending on the polish stuff it Will give a stunning result. I there are a lot of scratches ...   04-30-2021 08:28 pm

That would be great ...   04-19-2021 10:57 pm

Not all the fastners orders at robey Will work i found out, i Made my own fastners for the trunk trim. Also not all of ...   03-15-2021 07:49 pm

Think you need a large travel master cylinder BMW has those, but the are build in the pedalbox. If needed I could look if I have a ...   07-05-2020 03:40 pm

First picture of Dakota, Mine is sitting on the door On the opposite site, and not on the body. Can’t upload the foto. ...   07-05-2020 03:30 pm

Welcom, Looks great to me, rims fit nice with the car. Also the roof fits nice with the color. ...   06-24-2020 09:10 pm

How about some pictures, gives a bit more by your story ...   06-20-2020 04:47 pm

If you have long legs, I would chouse a dish wheel, gifs a bit more leg room. ...   06-18-2020 08:36 pm

I already opened up the wire loom from the fusebox to the foot compartment, to check if there also issues can be found. The only wire ...   06-11-2020 11:08 am

Have to solve some power issues I guess ...   06-08-2020 09:36 pm

New view ...   06-07-2020 09:28 am

That’s the engine bay when I bought the car 6 months a go. ...   06-06-2020 08:34 pm

Some spare parts ...   06-06-2020 08:01 pm

Rear ...   06-06-2020 08:00 pm

Front ...   06-06-2020 07:59 pm

I did putt u short movie of the first start on FB today. Still need some tuning to do, carbs and ignition. Also u bit of fuelpressure ...   06-06-2020 07:50 pm

Let’stry to upload some photos ...   06-03-2020 08:26 pm

This weekend fixing the carbs, and waiting for the Holley fuelpressure regulator. Than i can try to start the car and see what’s happening. So ...   05-28-2020 09:04 pm

Yup, no problem taking just the cap off, the cap fits ly one way due to a notch on it. It’s easier when the carbs are ...   05-28-2020 08:12 pm

One pic with the crank at TDC and the cams not timed up perfectly The belt has now been tensions and the engine has turnd over ...   05-28-2020 08:44 am

Everything lined up aften mounting the belt. ...   05-28-2020 08:42 am

The book says that the marking on the aux shaft should point towards the center of the crank bolt. I did it that way, see ...   05-28-2020 08:30 am

Almost read with all off the small jobs, -handbrake light - radio - dash lights - air valves at foot space, working now - door seals replaces - door locks set, ...   05-23-2020 08:51 pm

I am installing one at the moment, The extra seal is not pressend, but I als read on the Facebook page that they don’t leak. ...   05-18-2020 11:14 pm

I found out dat also the rubber seals from the throttle axle were shot. So I would advice a full refurbishment of the carbs to. ...   05-15-2020 06:38 pm

The big kopper one is ideal when you want to replace the jet. ...   05-14-2020 04:47 pm

The top one, is easy but becarvul, clean outside, spray some tread lube around, wait a bit and with a small screwdriver pull it out. ...   05-14-2020 04:34 pm

Here is an other model from kopper, no idee what the difference is.this one fare less fragile. If possible I would like to use this ...   05-14-2020 01:45 pm

Here is are some foto’s ...   05-14-2020 11:12 am

Do you mean the big plug in the center of the bowl? If so be very careful with it it has plastic parts, I could ...   05-13-2020 11:17 pm

That looks super 😁 ...   05-08-2020 06:36 pm

I bought the rubber ones , and I will see what happens ... I’ll make the surface super clean bevor installing the gasket and covers. The cam ...   05-01-2020 09:15 am

Did some investigation today about leaking cam covers. I found out that leaking mainly from the exhaust cam is not very strange. Because the oil return holes ...   04-30-2020 07:48 pm

Good topic Found out that from my oil pump the outer ring was broken in 2 But a fast replacement from Kees fixed te problem I hope. ...   04-30-2020 05:03 pm

No I am not they original owner, I got my copy from Martin Robey as a present with a large order spare parts. I try to ...   04-25-2020 07:11 pm

Here is a copy of mine, also with some strange notes ...   04-25-2020 08:43 am

That looks awesome dude, have lots of fun with it! ...   04-14-2020 10:01 pm

Lots of work done the last weeks - all bushings front and rear - weelbearings front - engine and gear mounts replacement - differential oil - brakes rear - refurbishing front ...   04-12-2020 02:05 pm