Don and Frank, Your Hubs will be on their way tomorrow. I will let you kn ow tracking once i have the number. Thank you and enjoy! Regards Peter ...   03-28-2017 11:30 am

DonBurns wrote: I believe we need an email address or PayPal account of some sort? Thanks- Paypal request sent Don, Thank you. ...   03-26-2017 06:56 pm

DonBurns wrote: I believe we need an email address or PayPal account of some sort? Thanks- Hi Don, Please let me know your email address via PM, i ...   03-25-2017 11:01 am

Frank Schwartz wrote: Yes..you can go to PayPal.com and open an account..they charge to your banking checking account. Widely used and very safe...you pay ...   03-25-2017 10:59 am

Hi All, Apologies for my tardy reply. All i need is an email address and the country your in. I will send through a paypal ...   03-25-2017 10:52 am

Updated the Price in the title, appologies for the late reply. Ps we have a holiday weekend coming up this weekend so i may not reply ...   01-24-2017 09:53 am

Funny you say that, i have one in the car and one on my desk now. :) ...   11-29-2016 06:08 pm

Thanks Tim, I've started a new thread on this as we have the final version done. I did a check on a worn belt: Static tensioned at ...   11-29-2016 09:27 am

Did a minor update today to make sure the Nyloc is fully engaged on the stud. Please check when installing that you have ...   11-29-2016 09:12 am

1) ...   11-29-2016 09:11 am

Jensen Healey Specific Manual Eccentric Hub. AUD$125.00 + 40.00 Express Shipping for 4 - 6 Business days (tracked) ~ USD$125-135 including shipping depending on exchange rate ...   11-29-2016 09:10 am

Front View: Untensioned ...   11-25-2016 02:00 pm

Jensen Healey Specific Maual Eccentric Hub ...   11-25-2016 01:33 pm

Jensen Healey Specific Manual Eccentric Hub Ditch the 2x 6005's and replace with the superior 1 piece Timing Belt Bearing SKF 414871A or the Flennor FS03299 ...   11-25-2016 12:52 pm

Jensen Healey specific hub coming along nicely. Directly squared over the crank pulley. Next we mill the hex, given the design it will be ...   11-25-2016 12:51 pm

The shoulder that touches the boss on the seal cover can't be enlarged. It presses through the bearing bore from front to rear, so bore-size ...   11-22-2016 06:25 pm

If I understand you correctly, what you need is a version of the Lotus eccentric hub with more shoulder and less spigot... correct? Correct. I thought ...   11-22-2016 05:23 pm

Update This is a no go, the spigot diameter is fine but it is too is too long for the J-H front housing. Additionally once we ...   11-22-2016 10:32 am

My thoughts also Tim only you combined it all in to one sentence... Well put! -  "If the J-H and Lotus tensioners are functionally ...   11-13-2016 09:33 am

Thanks Tim, That's most of the info i needed. I will measure the stock J-H spigot/male boss that pushes into the block and compare ...   11-13-2016 04:46 am

Esprit2 wrote: qwerty wrote: Is this arc to the outer hub normal or wear?It might be normal wear, but it was not apart of the original ...   11-12-2016 03:17 am

This little thingy has become an invaluable tool while troubleshooting the timing belt so i'll elaborate. It looks like lot of steps but it's ...   11-11-2016 03:05 pm

Esprit2 wrote: Thanks for posting about the BECO bearing. I've not heard of that one before, and I'll add it to my list. Regards, Tim Engel Thanks ...   11-11-2016 10:03 am

Is this arc to the outer hub normal or wear? ...   11-11-2016 08:23 am

BECO 6005 BHT 150 ...   11-11-2016 08:21 am

Gaaahhh.. Replaced the belt and pulley today and although the old belt was tracking almost spot on center of the sprockets before the install ...   11-11-2016 08:20 am

Thanks Tim, No specific issue other that observing that the stud was rotating as well as the hex adjuster while removing. Remember i adjusted it the ...   11-10-2016 08:43 am

No clearance issues at all, breezed it in with the stock washer. Standard M6 x 25 Cap Screw as pictured. Head Dia 10mm, smaller than a hex ...   11-10-2016 12:59 am

Tim would placing a bit of threadlocker (Loctite Medium Strength 243) on the stud into the block be a good idea? I noticed while tensioning ...   11-09-2016 09:58 am

They should all be the same OD regardless of type as per the standards, though cheese head and the button's allen key size is from ...   11-09-2016 09:15 am

Esprit2 wrote: Some Allen drive cap screw heads (cheese heads) are taller than others, and can rub on the back of the pulley. ...   11-08-2016 09:48 am

G'day Clint, I thought the same abou the WSM, maybe this is why there were a few belts jumpimg teeth in the past. I posted ...   11-08-2016 01:45 am

Finshed tool, sweet. ...   11-07-2016 08:12 am

And now in the CORRECT POSITION ...   11-07-2016 08:03 am

Thanks Tim, good rule to start with. Here is mine in the WRONG position, has been like this for some time!! ...   11-07-2016 08:01 am

Yes the upside down is a reference to the eccentric, nice one Clint, that may be why my lower A arms are back the front ...   11-06-2016 05:40 pm

Does that look pretty bloody loose too? I haven't touched it. ...   11-06-2016 09:20 am

Just approched this bearing today, looks like i have the integrated (once piece) roller AND it's installed up side down. I'll see what i can get ...   11-06-2016 09:09 am

dwalls1 wrote: Does the Sikaflex set up hard like epoxy, or softer like silicone? No, definitely not a hard epoxy. A Flexible silicone. ...   11-04-2016 03:10 pm

and now filled with Sikaflex. The back end if blocked off with a cut out of another length of timing belt on it's side with ...   11-04-2016 08:43 am