| ||||
|
Posts by jomac | |
---|---|
71 posts | Showing posts 1-40 of 71 |
Electrical & Instruments > Electrical (0 replies - 1162 views) I recently replaced my original fuse box with the new one from martinrobey.com part number 93065. I started getting intermittent lighting issues . ... 05-08-2023 06:08 pm Electrical & Instruments > Lighting (2 replies - 1647 views) Thanks ,I'll try it. ... 04-28-2023 02:06 pm Electrical & Instruments > Lighting (2 replies - 1647 views) By design does the door Courtesy light come on when either the driver side or passenger door is open, my light ... 04-27-2023 06:40 pm Electrical & Instruments > fuse box (2 replies - 2433 views) Correction the fuse box I got from martinrobey.com is a 3 fuse and same as the original with slight changes. I plan cutting ... 12-16-2022 01:25 am Miscellaneous > Rack and Pinion (11 replies - 4933 views) Redracer
Thanks , also, would you know the i.d. of the bushing that you used. I believe its 5/8 " , but not sure.
My thought ... 09-28-2022 12:13 pm Miscellaneous > Rack and Pinion (11 replies - 4933 views) Redracer
How do you replace the steering bushing at the firewall? I can't see it from under the hood. ... 09-28-2022 02:04 am Miscellaneous > Rack and Pinion (11 replies - 4933 views) After trying a tighter tolerance fit to pinion, it made no change in the play, but after a closer look found the movement ... 09-27-2022 08:47 pm Miscellaneous > Rack and Pinion (11 replies - 4933 views) Redracer
Thanks for the info, I'll make a shim if necessary.
But one question , when I lift off the top plate is there anything ... 09-26-2022 06:38 pm Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 6801 views) Thanks for all the responses, this will be my winter project.
Last winter I did a new clutch, one piece driveshaft, Holley sniper efi And pertronix ... 09-26-2022 12:20 am Miscellaneous > Rack and Pinion (11 replies - 4933 views) Redracer,
I have not done this before can you explain more. Do I add more shims or place them elsewhere?
What is the lower plate for? What ... 09-25-2022 10:07 pm Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 6801 views) sorry for the long delay , harborfreight.com sells a engine bar to support the engine from above using the fender flanging as support for ... 09-25-2022 02:41 pm Miscellaneous > Rack and Pinion (11 replies - 4933 views) Has anyone adjusted the pinion gear preload. my steering has
a slight play while driving. I checked out the steering shaft u joints they are ... 09-25-2022 02:31 pm Electrical & Instruments > fuse box (2 replies - 2433 views) Has anyone replaced the current 3 fuse box with the new 4 fuse box part number 93065. looking how you did it.
my current one ... 09-09-2022 08:09 pm Suspension > steering u joint (1 reply - 2161 views) does anyone know the shaft sizes and number splines for the lower steering u joint, any local usa sources. ... 09-02-2022 08:19 pm Projects > fuel injection for 907 engine (1 reply - 2166 views) Took me 3 months complete this project.
Requiring new fuel tank, fuel lines, fuel pump, throttle linkage and a custom fabricated intake manifold extension.
I was well ... 07-17-2022 04:20 pm Miscellaneous > Steering geometry (2 replies - 2634 views) Thanks for the info, I checked my camber it's within specs. I'll need to rotate my tires more , they're showing more wear on ... 11-20-2021 12:05 pm Miscellaneous > Steering geometry (2 replies - 2634 views) I am planning on refurbishing my front suspension, I believe my camber angle is too negative angle. Specs states toe in 0 ... 11-19-2021 02:10 pm Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 6801 views) Thanks for all your advise, looks like an engine pull next. ... 11-16-2021 01:16 am Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 6801 views) Ok. Rtv is not a good choice , however , it doesn't answer my question can you drop the oil pan enough to gain access ... 11-08-2021 12:07 am Engine & Transmission > Oil pan gasket or seal replacement (10 replies - 6801 views) Has anyone tried to reseal the oil pan by unbolting and dropping pan straight down and resting in the front crossmenber. I looks like there ... 11-05-2021 11:25 pm Projects > Flywheel bolt replacement part (7 replies - 4508 views) Can anyone tell me the size of the flywheel attaching bolts, I am looking a replacement part number I can buy a auto supply store ... 08-29-2021 10:17 pm Miscellaneous > steering wheel (2 replies - 3291 views) I would like to update new stock steering wheel. Can someone advise me on what size of splined adapter I need and who supplies them. ... 04-09-2021 01:12 pm Engine & Transmission > driveshaft 5 speed (10 replies - 7924 views) THANKS FOR THE ADVISE. it does sound like its a rear end issue. who did jensen have supply the diff, i read that they used ... 11-09-2020 09:10 pm Engine & Transmission > driveshaft 5 speed (10 replies - 7924 views) i may a stated it wrong , the pinion shaft does not move
its the drive have assembly can slide back and forth along the yoke ... 11-09-2020 06:50 pm Engine & Transmission > driveshaft 5 speed (10 replies - 7924 views) today i did inspection on my 2 piece driveshaft. the shaft assembly is like new condition. the bearing is fine and the rubber boot the ... 11-09-2020 04:38 pm Engine & Transmission > driveshaft 5 speed (10 replies - 7924 views) today i did inspection on my 2 piece driveshaft. the shaft assembly is like new condition. the bearing is fine and the rubber boot the ... 11-09-2020 04:38 pm Engine & Transmission > driveshaft 5 speed (10 replies - 7924 views) does your jensen have a 4 or 5 speed trans. and is the driveshaft 1 piece. i have a 2 piece design for the 5 ... 11-07-2020 11:11 pm Engine & Transmission > driveshaft 5 speed (10 replies - 7924 views) my jensen has a 2 piece driveshaft with a center bearing.
i noticed when under the car as i rotated the driveshaft
in makes a jingling noise.Thought ... 11-07-2020 09:41 pm Miscellaneous > sudden loss of power, for a while!!! (2 replies - 3544 views) I experienced today while driving the motor began to sputter ,loss of power and would not want to accelerate.
It lasted for a short time ... 09-07-2020 04:39 pm Miscellaneous > engine oil type (6 replies - 6874 views) I never did an oil flush.How do you apply the oil flush (twice), also,several gunk products which one do you use. ... 09-01-2020 05:33 pm Miscellaneous > engine oil type (6 replies - 6874 views) has anyone tried different engine oil, the castrol 20w50 is sometimes hard to find, i get mine a walmart. how about mobil one ? what ... 09-01-2020 01:00 pm Engine & Transmission > Hydraulic clutch conversion (2 replies - 4104 views) Has anyone tried to convert to hydraulic clutch setup. My attempt with using an off shelf clutch master cylinder and slave , I could not ... 07-04-2020 01:40 pm Carburetors > carburetor (12 replies - 13861 views) What is the correct oil level in stromberg carbs.
I am looking for a reference dimension.
Measuring from the top of the casting opening to the
oil ... 01-10-2020 09:45 pm Carburetors > carburetor (19 replies - 20880 views) my electric fan came with a 165 -185 thermostat, my heater hose line had old rusted out manual on/off valve which i removed to replace ... 09-24-2019 12:13 am Carburetors > carburetor (19 replies - 20880 views) i had the same issue, higher idle as it warms up, spring change appears to keep the idle more constant. regarding your radiator fan, i ... 09-22-2019 07:26 pm Carburetors > carburetor (19 replies - 20880 views) FYI, we always hear about replacing the diaphragm , but i also replaced the spring air valve return. it made the idle smoother and for ... 09-12-2019 07:33 pm Miscellaneous > interior (0 replies - 3091 views) FYI, if your rear view mirror needs replacement, i picked up one at mossmotors.com. Part number 801-085, $40. It comes with stem and plastic mount. ... 01-22-2019 01:17 am Brakes > brakes (1 reply - 4673 views) I recently rebuilt a spare set of front calipers with new pistons and seals. I bench tested them before installing them. noticing when bench testing ... 11-30-2018 11:17 pm Body & interior stuff > carburetor (4 replies - 6805 views) Tom
I have e3 3.46 model spark plugs, all plugs look good. using magnecor 8mm wire, they look good bought them 3 years ago... 3000 ... 11-15-2018 03:57 am Body & interior stuff > carburetor (4 replies - 6805 views) recently drove my JH. i notice engine ran a little rough while cruising in high gear. air temp was about 30 and engine was running ... 11-14-2018 09:54 pm | |
Current time is 07:11 am | 1 2 |