never paid much attention to the VIN# on my old gal, she is showing 11001, on the stamp pad. I know she is an early ...   04-13-2021 05:19 pm

just checked the depth on a newer sprocket and it was .090, so my older sprocket has significant wear .068, and will be ...   03-02-2019 09:17 pm

can anyone tell me the minimum depth of the cam sprockets teeth before it is considered rubbish?? Currently they are at .068 Thanks ! Mark. ...   03-02-2019 12:25 am

Anyone have a tip on how to best fill/add trans fluid to the Jensen 4 speed without spilling 1/2 the container? I don't have ...   08-18-2018 10:20 pm

Thanks for the information and diagrams!!!, I wondered why the car didn't run any different with the vacuum hoses capped off as opposed to being ...   03-10-2018 08:41 pm

On my 73 MK1 ,the vacuum line running from both the ZS carbs to the vacuum control valve, then it is shown going to the ...   03-10-2018 02:04 am

Does anyone know the thread size/pitch for the MK1 lug nuts? any listed sources for replacement - Aluminum Lug nuts? Thanks! ...   01-13-2018 04:42 pm

Thanks!!! ...   01-06-2018 11:49 pm

If the charcoal particles were removed from the canister (cracked case) would keeping the vent line from the fuel tank and then from the canister ...   01-06-2018 11:14 pm

Thanks! Just what I needed to see, much appreciated Mark ...   08-05-2016 10:35 pm

Can someone send me a pic of the proper mounting location and routing of the seatbelt reel on the rear wheel well area? I think ...   08-03-2016 01:59 pm

Can anyone tell me if the TR6 seat covers are the same as the Jensen Healey seat covers? the size and shape of the seats ...   07-25-2016 11:48 pm

Has anyone documented the correct steps to install a convert. top cover AKA parade boot. plenty of snap came with the new cover but ...   07-16-2016 10:13 pm

Thanks answerman! I'm a big fan of doing as little as possible to get the job done. Glad I asked before removing the whole gauge ...   07-01-2016 02:39 pm

Can the Tach be removed from the gauge cluster by itself? I need to install the circuit board to correct the Pertronix issue. Thanks! Mark. ...   06-30-2016 09:02 pm

Tensioner pic ...   05-31-2016 04:02 pm

Here is a pic of my Tensioner 1973 Made a cheap but effective tightening tool from a parts bin window regulator tool $5.00 just ...   05-31-2016 04:01 pm

the article you mentioned did help to put the pieces of the puzzle together. I eliminated the white / yellow wire from the coil to ...   05-23-2016 04:33 pm

Anyone know what the lone white wire that was connected to the original solenoid goes to / from ? can you also include a pic ...   05-21-2016 03:47 pm

Thanks! just downloaded a couple of wiring diagrams and trying to make sure I got it right, would love to see what a functioning hookup ...   05-21-2016 03:43 pm

My positive cable and associated wiring looks different from yours, cant really see where any of your wires are mounted, but thanks for the picture, ...   05-20-2016 03:27 pm

who has replaced their orig. starter with the gear reduction starter from British Starters .com? Had a wiring question and no one at B. Starters ...   05-19-2016 08:53 pm

I'm not sure of how the VIN series is categorized, it does seem to be an early car, as the motor I.D. shows it was ...   04-23-2016 03:00 pm

Anyone know of this car? white 1973 JH vin 11,001 purchased in MD. no info. from the broker who sold me the car. no ...   04-22-2016 06:54 pm