Hi Nigel My Bad, you are right, I will make a photo from the actual assembly later today. Thanks a lot for your help. BR Kim ...   06-18-2015 06:50 am

Hi Nigel, I guess that it must be the same hole as the spring 20. using the lower hole will forse the spring 21 to slide against ...   06-18-2015 06:03 am

Hi Nigel, Is this the same hole where I attach the left side of the spring 20?? BR Kim ...   06-18-2015 05:49 am

Hi I am having problems with my rear brake binding. I suspect that the problem is related to the assembly of the hand brake system. On the attached ...   06-17-2015 08:01 pm

Hi Esprit, I measured the liners to be between 95,28- 95,32 pistons are measured to be between 95,10 - 95,13 as you can see the best clearance i ...   04-26-2015 05:56 pm

I have opened the engine, and unfortunately the piston to liner clearence is app 0,2 mm which according to the manual is to much. The liners ...   04-26-2015 05:50 am

Hi If I run the car at a constant speed of 50 MPH there is no smoke. Then If I floor it the car accelerates but ...   04-25-2015 02:45 pm

sorry thread is "renovated engine burning oil" BR Barthol ...   04-19-2015 09:26 am

Hi I had the same issue on my 79 engine. I changed to the semi automatic tensioner which uses two other holes. I guess that if ...   04-19-2015 09:25 am

Hi again, Just measured my valve stems and the "side to side " movement of the valve at 10 mm open ( using a dial ...   04-05-2015 09:15 am

Hi, I have taken off the head ( engine out )and looking into the cylinders there is a big clearence between the cylinder and the piston. With ...   03-28-2015 05:04 pm

hi all Thanks for all the help . Esprit, that was a lot of valuable information:-) I Decided to change the tightener, which turned out to be a ...   03-28-2015 06:42 am

Hi All You are right , I do not think I can repair the Stud with the Engine in the car. As I have both Treads for ...   03-23-2015 06:22 am

I have no idea on how the bottom end is built . It was done from the Guy in Uk from who I bought the ...   03-22-2015 11:15 am

Hi Tim, Just forgot, The car is NOT for Granny Driving. In my opinion also old motors is supposed to be used as intended. It will definitely see ...   03-22-2015 06:59 am

Hej Tim, Engine is supposed to be a 1979 907 standard engine with the standard liners( they are iron- magnetic) / pistons, Liners is honed ...   03-22-2015 06:55 am

Found the error. I ran the engine for a little while closed the throttle and just rolled to a stop in 2 gear,then immediately removed the ...   03-21-2015 06:52 pm

Hi Joachim, Interesting reading. On my old Bikes I have used something in between. Running it through the gears, but gradually increasing RPM´s being very carefull to not ...   03-20-2015 01:35 pm

Hi Gordon, I run it on Mineral oil 15/40. And the smoke is a lot, not in idle but during acceleration 2-3000 rpm . I have ...   03-20-2015 10:54 am

Hi Gordon, I run it on Mineral oil 15/40. And the smoke is a lot, not in idle but during acceleration 2-3000 rpm . I have ...   03-20-2015 10:54 am

Hi Guys, After installing my 2,2 renovated engine i really understand why people says that stroking the engine is the single best thing to do to ...   03-20-2015 07:07 am

Hi Gordon, Thanks a lot , I will leave the manuel tensioner on :-) Br Kim ...   03-14-2015 11:12 am

Hi all, I have just finished installing my 2nd hand 2.2 907 engine.With the engine I also got a semi automatic cam belt tensioner. I now have ...   02-28-2015 08:17 am

Hi Thanks a lot Now my breather just goes to the ground BR Kim ...   02-04-2015 07:09 pm

Hi Can anyone tell me what I am supposed to connect to the huse connection on the lower rear side of my Dellorto airlifted box. Inside the ...   02-04-2015 06:27 pm

Hi Tim you were spot on or almost Looking through the progression hole showed that barrel no 4 was half a hole ahead of the other ...   01-26-2015 04:00 pm

Hi Jim and Tim, Thanks a lot. That is a lot of info and definitely something to work with. Using the parts I have i have changed ...   01-26-2015 05:54 am

Hi Forum, I have just finished my 2.2 ltr engine and put it bask in the car. Specs Cams 104/107 Comp ratio 9,35:1 ( Meassured ) comp meassured to 150 ...   01-24-2015 09:57 am

Hi, Aftar I have changed my engine I am experience problems with my Generator. As I just wanted to turn my new engine with the starter, I ...   01-02-2015 02:38 pm

Hi, I have changed my clutch and have now assembled the gearbox to the engine. My concern is with regard to the clutch release arm. Without the tension ...   12-13-2014 12:29 pm

Hi All, Going to put in my 2,2 ltr engine i got to think about a few things The guy I bought the engine from did the ...   11-20-2014 07:03 pm

Hi Rick, This might be way off but it is an easy check. During the Summer I experienced a similar intermitent noise coming from my Engine compartment. I ...   11-19-2014 06:26 pm

Hi Nigel, This was as suspected, thanks a lot for the confirmation. BR Kim ...   11-17-2014 07:02 pm

Empty engine bay ready for cleaning ...   11-16-2014 11:42 am

Engine coming out ...   11-16-2014 11:41 am

2nd photo of old engine ...   11-16-2014 11:39 am

Hi I am exchanging my 2.0 907 engine with a later 2,2 907 engine. My question is tabour the extra CW connection stud I have on ...   11-16-2014 11:38 am

Hi, I have had problems with my servo unit lately and it has turned out they my old vacuum hose was blocked, needs to be replaced. I ...   08-03-2014 03:35 pm

Hi I am looking for the Vin number in my car, I have found the plates on the drivers door , on the dash board and ...   07-09-2014 02:41 pm

Hi I am mounting dellortoes on my jh, and I got the manifold with the "long cooling pipe" see attached photo. My problem is that there ...   06-19-2014 07:13 pm