| ||||
|
Posts by atgparker | |
---|---|
90 posts | Showing posts 1-40 of 90 |
Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Well 11602 got the engine rebuilt with a matching set of mk2 pistons and rod assemblies that all have tapered wrist pins. They have ... 08-01-2022 02:12 am Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Tim,
Many thanks for your wonderfully detailed response. The HG let go last December with the drive up to Willow Springs for an Extreme Speed ... 06-24-2022 09:18 pm Brakes > Brakes (23 replies - 36561 views) All thread and clevis to the OEM brake lever with unpainted toggle bar that was lacking the swivel at the center when I took this ... 01-26-2022 03:52 am Brakes > Brakes (23 replies - 36561 views) How it looks from the wheel well. Note PVC pipe used to center CRX disk on the axle. ... 01-26-2022 03:51 am Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Yes the axle shaft did get replaced Delta bailed me out in that area of disgrace. While I was at it the rear axle ... 01-11-2020 10:44 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Thank you for the heads up on this point. I concur with your assessment. I have a 1999 Honda CRV strainer on my fuel ... 11-26-2017 06:26 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) SCCA-Solo event at Fontana just this last October. Thrashed the OEM motor mounts and ruptured the firewall shock mount all before the ruddy fuel pump ... 11-26-2017 05:40 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) SU seems to be really nice and a lot better designed than the unvented Hardi. This SU has the solid state electronics and has ... 11-26-2017 05:36 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Three weeks ago my two year old Hardi fuel pump quit.
Looks like the single click was due to fuel ingress into the PCBA and the ... 11-26-2017 05:33 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) When the motor mounts failed the fire wall got fatigued and cracked badly. So I made up this reinforcement from some 1/8 inch thick ... 11-26-2017 04:47 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Replaced motor mounts with Land Rover D-90/Discovery 1 units. Twice the diameter of the OEM and about the same thickness. The aluminum hole saw ... 11-26-2017 04:35 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) I got the bonnet and front fender repainted back in July 2017. A lot of block sanding priming and boom the rest of the ... 11-18-2017 08:37 am Suspension > Installing front sway bar (33 replies - 67622 views) Frank, Get some longer bolts and some tubing to space the washers and bushings so that sway bar is above the truss rod that has ... 06-26-2017 06:00 am VIN Database for Jensen Healey & Jensen GT > Jensen Healey & Jensen GT VIN Database (342 replies - 588287 views) VIN: 11602
Good Running Condition,
Came with 45 DCOE Weber's and European Specification intake manifold. They have been rejetted from what was OEM spec for ... 06-19-2017 09:07 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Picture of my method for spreading the inner fender panel out to match the Mk1 fender I aquired from Brithish Masters over the week end. ... 06-19-2017 08:53 pm Electrical & Instruments > Fritzy Tachometer (41 replies - 106503 views) I wonder if the modification to the tachometer has interferences like I discovered with the SPIDA kit? You would have to disassemble the tack ... 06-15-2017 01:28 am Brakes > Brakes (23 replies - 36561 views) Brackets for holding Centric Flex lines with M10 x 1.0 Thread adapters to 1/8 NPT.
All that lovely new bed liner paint on the axle needed ... 05-27-2017 04:40 am Brakes > Brakes (23 replies - 36561 views) Hydraulic line routing to chassis ... 05-27-2017 04:33 am Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) This modified Addco Sway bar arrangement gets the bushings and washers parallel with the OEM tab on the lower suspension arm. The thing with ... 05-27-2017 04:17 am Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) McMaster-Carr parts for Pertronix FlameThrower distributor shaft improvements:
Thrust bearing is: 5909K31
O-Ring Supported U-Cup is: 9505K17
Mcmaster-Carr Parts for Door Hinge Rework:
Door Hinge Pin Replacement:
Punch Pin Blank ... 05-26-2017 05:05 am Brakes > Brakes (23 replies - 36561 views) Adapter plate for the caliper on the axle housing.
This took three tries in thin plywood on a scroll saw to perfect for the cable angle ... 05-15-2017 02:45 am Brakes > Brakes (23 replies - 36561 views) Header plate used to secure cable outer housing in the tranny tunnel.
Those stepped sheet metal hole-saw's are the ticket for popping in the ... 05-15-2017 02:38 am Brakes > Brakes (23 replies - 36561 views) Cable routing from caliper to pivot axis of upper control arm bolt. It was like these cables were made for the car.
Note the rubber ... 05-15-2017 02:04 am Brakes > Brakes (23 replies - 36561 views) Twin Cable to Handbrake lever modification. All thread passes back through OEM cable hole with plastic tubing slipped over the all thread to keep ... 05-15-2017 01:44 am Brakes > Brakes (23 replies - 36561 views) Emergency Brake Cable Management using the OEM CRX cables. note the upper control arm bolt is utilized for the bracket fixing. The cables ... 05-15-2017 01:44 am Brakes > Brakes (23 replies - 36561 views) CRX OEM Brake cable bracket fabricated from some 1.00" wide steel strip, a wave washer flat washer and E-clip retaining ring. ... 05-15-2017 01:14 am Brakes > Brakes (23 replies - 36561 views) Honda CRX brakes work with the Honda OEM emergency brake cables. I pitched the stock JH cable and rod as it doesn't really work on ... 05-15-2017 01:11 am Brakes > Brakes (23 replies - 36561 views) Awesome stuff! Please advise on caliper and disk used. Been looking at this modification for quite some time but looks like you found ... 02-24-2017 09:47 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Bad day yesterday with all the rain hydroplaned and spun the car and bent the axle shaft. Does anyone have one for sale?
I will ... 02-18-2017 02:38 pm Cooling > Electric fan sender (9 replies - 19104 views) I have a European specification intake manifold and what I did was drill and tap a hole next to the OEM sending unit for the ... 12-18-2016 01:38 am Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) Fleanor FSO3299, Gates T104RB, Tensioner Hub:
At 74,200 miles I installed a new timing belt, pulley and idler hub (Care of Peter Van Ruth, AKA Down ... 12-17-2016 01:07 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) 11602 Hits 70,000 Miles on the odo this week.
New shoes to boot! ... 09-09-2016 01:25 am Engine & Transmission > W58 Gearbox (5 replies - 20695 views) I have had my W58 Gearbox in 11602 for a few months now and the not popping out of second gear is really nice.
I ended ... 09-09-2016 01:19 am Wheels > 205/60-13 Tires (36 replies - 85657 views) The Coopers are shot and got some 205/60-13 Pro Meters.
They measure more like 197 rather than 205 on the 5.5 OEM wheels. Are 400+ ... 09-09-2016 12:56 am Wheels > VTO Wheels (6 replies - 14289 views) 11602 gets a face lift with some Yokohama 205/50-15 ADVAN NEOVA A018-R's.
This combination weighs in at 37lbs
Wheel @ 19lbs.
Tire @ 18lbs. ... 09-09-2016 12:45 am Engine & Transmission > Speedometer gear (1 reply - 5119 views) On the shaft and inside the steel inner part of the gear there is a ribbed piece of sheet metal which is sort of sprung ... 05-04-2016 08:26 pm Wheels > 205/60-13 Tires (36 replies - 85657 views) I have had the pleasure over the past 2 years and 10 months to put 16,870 miles on the Set of Cooper Cobra's which came ... 05-04-2016 08:15 pm Engine & Transmission > W58 Gearbox (5 replies - 20695 views) Yes this is the very unit. I had to make a .375 inch thick spacer to jack the Cube up to get the ball and ... 04-23-2016 03:41 am Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) 11602 Got new rear axle bearings this weekend. Centrix bearings lack the o-ring groove to seal the gear oil in the axle housing. ... 04-18-2016 08:01 pm Projects > 1973 Jensen Healey Vin#11602 (40 replies - 96330 views) In my travels with working out a Toyota W58 conversion for 11602 I have found a source for a clutch disk with the following specification: ... 04-08-2016 03:50 pm | |
Current time is 06:32 am | 1 2 3 |