I took an old JH wheel and turned it down until I had a hub...then I drilled it to match a 2.5 spacer and the ...   06-20-2020 06:50 am

I think the JH hood had a hole there for the squirter. Since the GT had the squirter moved more forwards, that chrome button merely ...   05-07-2020 02:55 am

I think the JH hood had a hole there for the squirter. Since the GT had the squirter moved more forwards, that chrome button merely ...   05-07-2020 02:55 am

It seems that this event which was scheduled for June 4-8 has been cancelled. I learned that it is possible to be re scheduled in ...   04-05-2020 01:17 am

Hello, Tim. Good to hear from you. I don't know of any shop in that area ...but here in the middle of Tennessee, I am ...   11-28-2019 02:06 am

Unless I mis-read this posting, and you cannot get lower than 1200 rpm, there is a fine adjustment wheel on the distributor which if working, ...   11-19-2019 07:49 pm

Sure looks like the same switch to me...maybe one should buy it and see...I think Moss would accept a return if it did not fit... Frank ...   11-16-2019 05:58 pm

It could easily be the switch contacts...but on some cars it is merely dirty plug components..often plugging and unplugging it a couple of times sort ...   11-16-2019 12:23 am

That "O" ring is a #10...available at most car parts stores very inexpensive. Frank ...   10-14-2019 05:26 am

Don't forget the Jensen 2019 East meet in St. Louis this month (Sept) from the 18th through the 22nd. Seems a very few Midwest folks are ...   09-14-2019 12:46 am

Good news! Will you..and your car...be able to join us for the Jensen East 2019 meet in St. Louis next month???? Frank ...   08-19-2019 10:34 pm

IIRC on the bottom clamp of the ignition key bracket should be 4 numbers...Delta can make you keys to match that number. NEVER EVER have only ...   08-19-2019 05:31 pm

Moss Motors sells this...on mine, I had to exchange the plug as IFIC one is a female and one is a male...but that was no ...   08-19-2019 01:29 am

Which one in particular? Seems they are for V belts... Frank ...   05-28-2019 12:27 am

The Blue belt: I bought this one from the local O'Rielly auto part store. Not in stock, but a special order. No ...   05-26-2019 06:38 pm

Tim..and others: So what is the tension requirements for the blue belt. I do not have a tension measurement tool. Most of us with the ...   05-26-2019 06:34 pm

You are correct. The rubber insert is from earlier JHs and the metal emblem is on later ones..You cannot put that metal piece in the ...   05-23-2019 11:18 pm

I bought a pair of those Tornados and one broke..it's plastic....and plastic breaks Moss motors has the stainless mirrors in right and left, both in the ...   04-01-2019 07:31 am

Wow !!! I thought no one from Pete's family would ever come to light. Certainly glad you posted here. I was quite fond ...   02-18-2019 04:37 pm

AFIK the jumper between the two white feed wires is necessary. They are the feed wires for fuse 1 and 2...keep them joined. Frank ...   12-29-2018 03:18 am

Oh, oh...I just see you used Kimbroughs diagrams,....they are good, but not the JH supplied diagram... and not the one I use. Still, just ...   12-27-2018 07:57 pm

If you will look at the very center of your diagram at the top you will see a square drawing with twelve numbered contacts. ...   12-27-2018 07:49 pm

Correction: the correct email is patten1955@hotmail.com Frank P.S. I was having a senior moment.... ...   12-23-2018 08:20 am

My daughter,Patten Laurel, can sew you some silver braid in a clear plastic strip for a very nominal sum. You will need to remove the ...   12-23-2018 08:17 am

Ooops...I am "partially" incorrect. I somehow thought you meant the oil pressure. If you have an in line gauge, that is a gauge ...   12-19-2018 04:34 pm

No, no, no...you want to read the fuel pressure, not the oil pressure... and it should be in the fuel line...Remove the line going to the ...   12-19-2018 04:28 pm

If you can, measure the pressure at the carburetor feed (T) and if it is more than 2.5 pounds...again...get a pressure regulator..they are cheap Frank ...   12-18-2018 06:54 pm

If I am not mistaken, that fuel pump, and others of similar make, are supposed to be used with a fuel pressure regulator, You can ...   12-18-2018 03:03 pm

Bruce is right...the wire to the cigarette lighter is hot and if shorted out, the #3 will blow every time... Frank ...   12-10-2018 07:07 am

Fuse 3 feeds the clock, the dip switch on the light switch the right hand door light switch and the fasten seat belt light, which ...   12-09-2018 07:09 am

Good news!! Please keep us posted as to your progress. Frank ...   11-30-2018 09:38 pm

Another thought......if part number 13 wobbles and is loose, the steel pin that goes through the ball in the end is a much harder steel ...   11-30-2018 06:17 pm

I should think that with a new part #17 (Delta Motorsports), you should be a "go" If you still have the problem with first and 2nd ...   11-30-2018 06:08 pm

IIRC I had a problem like this. Under the car you will note the bracket that holds the end of the transmission has two slotted ...   11-25-2018 04:15 pm

Hmmm...that's a nice squirter...where did you fin that one...most of the ones I get are junk... And yes, I really did get my finger stuck...My son, ...   08-20-2018 04:58 pm

Harbor Freight #81746 $9.95 or equivalent... Frank ...   08-19-2018 01:11 am

This can be a real bugger...you can't see up there and you can hardly reach up there...but by all means don' t stick ...   08-19-2018 01:04 am

I'd like to see what Steve Luckett has on this....maybe he will read this and give us the "thread" Frank ...   08-16-2018 11:22 pm

oops typing error...that should be "why pay 375 dollars" Frank ...   08-11-2018 06:29 pm

That's pretty expensive...as I wrote, you can buy almost exact units from Moss Motors for the pair about 100 bucks...if you are a good do ...   08-11-2018 06:28 pm