Goldmember is gone, Baby, gone. For real. Both our LeMons cars were in a gravel pullout on the side of the driveway of ...   08-07-2018 01:47 am

Well, here's the update. We had stripped all of the original wiring harness out of the parts car that became the race car, partly ...   01-19-2017 05:18 pm

Thanks. I'm sure there's plenty of those in my local PickNPull. I just got an email from Colin Dray in NZ saying he ...   01-05-2015 02:03 am

Can you tell me what W58 trans you have that you like so well? Or what the donor vehicle was? ...   01-05-2015 01:51 am

I'm getting ready for a W58 swap in my track JH; my Getrag 5 speed has to be shifted with a soft hand to keep ...   12-28-2014 11:52 pm

Here's a few VIN numbers, as a catchup. #19377, which was a body from another unknown vin number car that I rebadged as 19377 because I ...   11-20-2014 08:13 am

I thought I'd start a thread on how and why we are now the proud and idiotic owners of a dedicated JH race car. For ...   11-20-2014 07:55 am

I'm finishing putting the motor back together after my daily driver was destroyed in a wreck last year and I don't have a straight spare ...   07-21-2014 05:01 am

Nice, useful sketch, Mark.   Thanks.  But that brings up a question for me: what's the tipping valve do?  I can't discern it from the drawing ...   06-20-2007 05:08 pm

 I've installed JHPS's big brake kit and stainless lines and I have a couple of observations and a complaint.   First, the braking is superb; linear ...   06-03-2007 02:52 am

Arghhh! I just wrote a long message about my fresh car, tried to include a pix of it which was refused and lost everything I ...   05-28-2007 12:19 am

Well, well.  I figured out why my JH wasn't running right.  And this is a good one.  Sometime before I installed my brand new DellOrtos ...   05-14-2007 03:18 am

The flakes in the tank story is a good one.  My tank is unknown, tho I did look it over well with a mirror before ...   05-04-2007 04:28 pm

Thanks for the quick reply, Kurt and Greg, I was using a stock SU fuel pump that I took apart and cleaned up.  It was pumping ...   05-04-2007 01:27 am

I'm taking off on a thread from a year and a half ago on the DellO 40 vs 45 forum (last used a year and ...   05-03-2007 04:29 am

I recently spoke with Delta, and the fellow there was a mechanic/salesperson for JH back in the day.  He says he personally came up with ...   05-02-2007 04:26 am

Thanks for answering, Greg.  I never know who's checking on these older, quiet forums. Well, Blimey, I didn't know JHPS sold K&Ns.  I bought them online ...   05-01-2007 05:46 pm

OK, annoying speed bump #    @#$&(*(&* : I've seen K&Ns in various underhood pictures but when I bought the oval ones that looked just like ...   05-01-2007 12:36 am

Yes, I do indeed have early regrinds: 907E0351Y, but ground till there's about .378 lift, which makes them appear to be Dave Bean regrinds.  They're ...   04-01-2007 01:18 am

Kurt, Your mention of using 110 pulleys for my 107 cams made me realize I didn't understand the subtle dynamics of all the cam timing threads ...   03-30-2007 04:49 am

What a pain, eh, Dan.  I'm in exactly the same place.  Just finally, after the better part of a day today, got the exhaust to ...   03-29-2007 08:03 am

Thanks for the response, Jim.  I have 3 heads and I think I'll pull my two spares and look them over carefully as replacements.  It's ...   03-24-2007 06:34 am

OK, being my first time at the "black art" of Lotus cam shims, it's obvious to me there's a fair amount I don't understand: I'm ...   03-23-2007 03:40 pm

I've got a set I just took off, too.  How many will you need to stack up to get within shim range?  8) ...   03-16-2007 04:21 pm

I am tentatively looking for the following cam bucket shims, in thousandhts: 60 X 2 64 X 2 65 X 2 67 X 2 69 72 73 81 95 and undoubtedly several others around these ...   03-15-2007 06:22 pm

I'm setting my valves for the 1st time and am looking for a supply of shims to play with.  Most of the ones I need ...   03-14-2007 10:42 pm

I was not so lucky removing my used windshield today; a tiny crack at the corner suddenly took a wild ride out across the middle ...   03-12-2007 10:51 pm

JH 19377: dead, rusted beyond belief after many years in Eureka, California; engine B7411 10232, reputed spun bearing, will be stripped and destroyed JH 19295: dead, ...   03-05-2007 04:38 pm