Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Suspension > Installing front sway bar

 Moderated by: Greg Fletcher Page:  First Page Previous Page  1  2   
New Topic Reply Printer Friendly
Installing front sway bar  Rating:  Rating
AuthorPost
 Posted: 10-24-2013 10:48 pm
  PM Quote Reply
21st Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
This angle allows the bushing stack to match the angle of the A-arm's tabs which come on the OEM suspension's lower arms . What is more with the spacer I used it clears the strut bar in this location and the cross bar is the only low point that will hit things should one miss judge the clearence. It seemed this was the best approach to get the bushing stack snug and have all the washers and spacers work without binding when you cycle the suspension. Unless you use the Addco "L" bracket I cannot see how to use the bolt and spacer they supply with the OEM tab. 205/60-R13's on OEM rims do rub on the bar at full lock with this arrangement. But the tire and smooth shape of the bar touch and do not really pose a problem.

Back To Top PM Quote Reply  

 Posted: 10-27-2013 09:07 am
  PM Quote Reply
22nd Post
roland11a
Member
 

Joined: 12-11-2012
Location: Stone. Staffordshire, United Kingdom
Posts: 80
Status: 
Offline
Strange looking at these after market Anti Roll bar setups! I've got a genuine one I presume from a GT or some early Vauxhall Magnum. This bar fits completley to the front sub frame and is mounted underneath the lower suspension arms. I would have thought it a bad idea to mount an anti roll bar part onto the subframe and part onto the body as the subframe is mounted on flexable rubber bushes . So allowing a sertain amount of movement between the two. Still if it works well job done.

Back To Top PM Quote Reply

 Posted: 10-28-2013 05:58 pm
  PM Quote Reply
23rd Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
I was wondering about those other holes in the sub frame as they looked like they could harbor a sway bar.

The bushing which fixes the rear of the sub frame to the unibody-chassis is perhaps the best candidate on the entire car to replace with a polyurethane replacement. Also the fasteners in my car, 11602 came with were undersized fasteners bolting this assembly together. So I replaced the sleeve and increased the fastener to a nice big 1/2-13UNC grade 8 bolt with a Nylock so that you don't have to torque the bolt to spec as you will crush the sleeve. The hole in the body will take the 1/2" bolt with out any drilling so I can only guess the smaller bolt was either a PO putting it there or JH choosing it for ease of assembly. You may need a spud wrench to get the holes in the frame and sub frame to align when you drive the bolt through. This might help with your sub frame mounted sway bar's response being quickened a bit if its still rubber and the bolts are the smaller ones.

In actuality the mounting of the sway bar to the unibody and the A-arms is mechanically a better means to spread the anti-roll loading into the chassis as it takes the sub frame to body flex out of the equation. Having said that the funky U bolts are starting to tare the sheet metal in the frame rail so I may have to plate the frame rail with some strip and perhaps weld in some blind nuts to secure the bracket for the bars OD.

Back To Top PM Quote Reply  

 Posted: 10-28-2013 06:04 pm
  PM Quote Reply
24th Post
roland11a
Member
 

Joined: 12-11-2012
Location: Stone. Staffordshire, United Kingdom
Posts: 80
Status: 
Offline
When I put my front crossmember back together I'll post a photo for interest sake. All off the car at the moment undergoing a rebuild .

 Big day tomorrow as the body is back from spraying.

Back To Top PM Quote Reply

 Posted: 11-28-2013 10:39 am
  PM Quote Reply
25th Post
roland11a
Member
 

Joined: 12-11-2012
Location: Stone. Staffordshire, United Kingdom
Posts: 80
Status: 
Offline
http://www.flickr.com/photos/99803698@N07/sets/72157638139249415/

As promised. The genuine part anti roll bar fitted.

Last edited on 11-28-2013 10:44 am by roland11a

Back To Top PM Quote Reply  

 Posted: 11-28-2013 08:09 pm
  PM Quote Reply
26th Post
Art DeKneef
Member
 

Joined: 03-12-2005
Location: Mesa, Arizona USA
Posts: 340
Status: 
Offline
Tried to view picture but the page redirected to Yahoo and wanted me to log in. No go.

Back To Top PM Quote Reply

 Posted: 11-28-2013 08:38 pm
  PM Quote Reply
27th Post
roland11a
Member
 

Joined: 12-11-2012
Location: Stone. Staffordshire, United Kingdom
Posts: 80
Status: 
Offline
Try These

Just got to attach the drop link once the springs are compressed

[










Back To Top PM Quote Reply  

 Posted: 11-29-2013 09:01 pm
  PM Quote Reply
28th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
That looks really odd compared to the chassis mount bars.

Back To Top PM Quote Reply

 Posted: 11-30-2013 02:16 am
  PM Quote Reply
29th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Yup it sure does. But the Addco chassis mounted bars end up having a longer effective arm as they are rear set by quite a bit from the OEM mounts shown above. So that makes the bar's relative stiffness less for a given diameter being the same with these two arrangements. It's no wonder that Huffaker Engineering did something completely different for the sway bar when they raced this car.

When I auto crossed mine a few weeks ago with the Addco bars in place I thought I was going to clean house. But the Koni's were wide open so there was no rebound damping resistance and the cars excellent steering response made short work of the excessive body roll but the transitions made nailing the desired route impossible.

I just hope the Koni's on the front are as mal adjusted as were the rear on 11602.

Back To Top PM Quote Reply  

 Posted: 06-26-2017 12:28 am
  PM Quote Reply
30th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
I'm stuck here with a ADDCO 101 sway bar that doesn't seem to want to fit. The tabs on the suspension where it is supposed to bolt on front is so close to the steering arm assembly that it is almost impossible to mount the sway bar... the steering rods prevent easy installation. I have two brackets included with the kit but no instructions or any indication of how they are to be used. I've read the instructions and also the previous posts here...and am still very confused...plus I cannot weld..(pacemaker will go crazy). Any help??

Thanks,
Frank

Back To Top PM Quote Reply

 Posted: 06-26-2017 06:00 am
  PM Quote Reply
31st Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Frank, Get some longer bolts and some tubing to space the washers and bushings so that sway bar is above the truss rod that has the large bushing and washer stack which passes through the sub fame. Look at my cars setup the vin is 11602. The tabs on the lower suspension arm are well suited when the bar is set up this way, unless the suspension arms were swapped from left to right at some point in the cars history?

Back To Top PM Quote Reply  

 Posted: 06-26-2017 06:41 am
  PM Quote Reply
32nd Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
Well, it does appear, upon close inspection that the two arms are crossed. If removed and swapped over then the mounting points will be correct. How in the heck does this happen?? Or did some PO swap them..or did the factory do it???
Seems that these can be both ways...that is on a couple of the JH's I have checked they are placed wrong..and then on a complete front end we recently purchased in a lot for parts, the mounting point is to the rear and is correct...what a mess this is.........

Frank

Back To Top PM Quote Reply

 Posted: 06-26-2017 08:26 am
  PM Quote Reply
33rd Post
Tim Murphy
Member


Joined: 03-22-2005
Location: Huntington Beach , California USA
Posts: 96
Status: 
Offline
Frank, I had the same problem years ago. The very experience JH mechanic who swapped arms said it was common, the factory installed the arms randomly, some both mounting points front, some both back. It didn't matter too them because the stock JH did not have anti sway bars.

Back To Top PM Quote Reply  

 Posted: 06-26-2017 07:04 pm
  PM Quote Reply
34th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
Frank & all:
the tabs for a sway bar should be pointed back. You have to drill a hole in the supporting "U" channel to put a "u" bolt through it. I don't recommend doing this as Parker's weld is much preferred if you MUST have one.
On the race cars, the tabs are pointing forward for mounting across the radiator shroud, but we also did not have a fan, which would be in the way.
A third option is to get a GT sway bar which mounts to the subframe itself, and not the "U" channel behind it.
Having said all this, rear sway bar is MUCH preferred as the car had a tendency for understeering/plowing, for which a front swaybar would only increase the understeer.
Over the years, the adjustable SPAX shocks with the rear setting 2 clicks/1/2 turn stiffer than the fronts, gave very good handling characteristics without any sway bars necessay. However, if you are trying to turn your car into a street racer, then you will need also expensive tires(tyres, for all you other blokes) to give you acceptable handling.

Back To Top PM Quote Reply

Current time is 05:58 am Page:  First Page Previous Page  1  2     
> Jensen Healey & Jensen GT Tech > Suspension > Installing front sway bar Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems