| ||||
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Replacement Switches, Turnsignal/ Windshield wiper assembly |
| ||||
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Replacement Switches, Turnsignal/ Windshield wiper assembly |
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Replacement Switches, Turnsignal/ Windshield wiper assembly | Rating: 
|
| Author | Post |
|---|
| Posted: 07-13-2005 05:38 pm |
|
1st Post |
|
edward_davis Member 
|
I'm trying to get all of the gremlins out of the lighting systems on my 74 JH, and I was curious whether there is a reliable source for replacement switches, or if someone knows of switches that I can fit into the dashboard. Also, the plastic ring on my turnsignal/ wiper lever assembly, the one that holds it onto the steering column, is broken. All of the switches in the assembly seem to work, but I have had to wedge it in place with spare bits of rubber. Are there replacement assemblies available? Is there a fix to my broken ring that someone else has come up with? Finally, in a sort of humorous vein, when I push in the wiper lever, which should activate the windshield washer, my tachometer is pinned above 8000. I can also hear the little pump motor going.... Any ideas why that might be happening?
|
||||||||||||||
| |||||||||||||||
| Posted: 07-13-2005 05:48 pm |
|
2nd Post |
|
Joel Member
|
maybe the wiper lever ups the turbo boost pressure? i think i need the same thing for my turn signal assembly. i have not taken it apart yet but it's loose in the column so i'm assuming some mounting bits are broken. if you find someone who has the parts please post so i can try to hunt them down too.
|
|||||||||||||
| ||||||||||||||
| Posted: 07-13-2005 05:53 pm |
|
3rd Post |
|
Brett Gibson JH5 20497 Member
|
Bruce Madden in Atlanta rebuilds those wiper switch's and all the other ones as well, super guy and does good work, I think his phone number is listed on this Web site some place, Delta has new switch's but they differ slightly, they probably even have the wipper switch but that is going to be big buck's. Cheer's Brett.
|
||||||||||||||
| |||||||||||||||
| Posted: 07-13-2005 10:43 pm |
|
4th Post |
|
Tim Knowlton Member
|
As fa r as the turn signal/wiper assembly I would look into purchasing one from MG. I believe they are the same units in the MGB or MGBGT. The nice thing about these units is that the arms are not quite as long and I personally like that feature. Good luck!
|
|||||||||||||
| ||||||||||||||
| Posted: 07-18-2005 07:33 pm |
|
5th Post |
|
George Member
|
I compared a later model MGB one directly with the one from my JH, and the only differences were: 1) as mentioned, the shaft is a little shorter; 2) two pins on the connector need to be switched, but the wire colors are the same, so that's an easy task; and 3) the white plastic collar that operates the turn signal cancellation is a little taller on the MGB switch. Not sure if this makes a difference or not, but I was planning on cutting it down, before I found a new old stock JH switch. Looks like it would be a fairly straight forward job, however. (hope this reply isn't too late to be of any help) George
|
||||||||||||||
| |||||||||||||||
| Posted: 08-08-2005 05:43 pm |
|
6th Post |
|
edward_davis Member
|
Well, I replaced the original switch with a new Lucas unit from Delta Motorsports. It was $130, but that's comparable to an MGB unit. Not only did it solve my problem with the broken mounting ring, but it also made the horn and high-beam headlights work properly. So I think it was money well-spent.
|
|||||||||||||
| ||||||||||||||
| Posted: 08-08-2005 07:31 pm |
|
7th Post |
|
slazo Member
|
I already have converted to the MG switch, and George is quite correct. 2 wires must be switched in the connector, and the collar cut down, easily done with a Dremel. Works quite well. Sheldon 1974 JH 15582 Chicago
|
||||||||||||||
| |||||||||||||||
| Posted: 11-10-2005 06:44 pm |
|
8th Post |
|
LambandAndy Member 
|
I recently bought a replacement turn signal switch from The 'B' Hive. Price was $79.95. Savings are well worth the extra 30 minutes work to install. http://www.thebhive.com Item # 320-205 Andy #15223
|
|||||||||||||
| ||||||||||||||
| Posted: 11-25-2010 04:42 am |
|
9th Post |
|
artmd Member
|
I had a broken mounting to my turn signal for about 15 years and finally decided to replace it with the Lucas assembly from Delta. I switched the wires without any problem but the blue collar was too long. I tried to shorten it with a Dremel as you described but I could not get it to fit right and it kept slipping and it would not automatically release. So what I did was remove the white plastic collar from my old assembly and replaced the blue collar. It works like new! The shorter arm is notable but not that big of a problem. You must be very careful when you remove the plate that holds the collar in place because the inner workings of the turn signal is also behind the plate and it is full of springs and small plastic parts. If you do not have the assemble level and remove the two bolts slowly everything will pop out. I learned it the hard way and had to buy a second turn signal. With this one I placed it in a vice, slowly removed the plate, placed the old white collar in place of the blue and I could not be happier. Art
|
||||||||||||||
| |||||||||||||||
| Current time is 06:07 pm | |
| > Jensen Healey & Jensen GT Tech > Electrical & Instruments > Replacement Switches, Turnsignal/ Windshield wiper assembly | Top |
