Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Ignition > Nothing happens in start position after working on dash wires

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Nothing happens in start position after working on dash wires  Rate Topic 
AuthorPost
 Posted: 09-08-2020 06:41 pm
  PM Quote Reply
1st Post
gvictora
Member
 

Joined: 06-23-2020
Location:  
Posts: 4
Status: 
Offline
Hello all. I bought chassis 12383 back in June. It ran well, but had a few minor problems. This weekend I replaced the dim dashboard lights with LED lights. I struggled some, and couldn't get the instrument panel all the way out, but managed to replace all the bulbs. The hardest part was reconnecting the speedometer cable which required sticking my hand way up high behind the dash. To do that I had to move a lot of wires in a "rat's nest" of wires behind the dash.

After putting it all together I went to start the car and absolutely nothing happens when I turn the ignition to the start position, no click, no lights dimming, nothing. I assume I did something to the wiring under the dash. The lights all work, the radio comes on, I can hear the fuel pump clicking, everything else seems normal. The voltage gauge slowly comes up to about 12 volts and truthfully, I can't remember what the voltage gauge used to read before I started the car.

This happened late last night, so I haven't really tried anything yet, other than I did try to jump start the car just to make sure it wasn't the battery. No difference.

Any suggestions on where to start my search and how to proceed? Electrical stuff is always my least favorite thing and what I seem to be worst at.

I'm frustrated because it's probably a simple thing, but I'm not really sure where to start. Any suggestions would be greatly appreciated.

Back To Top PM Quote Reply  

 Posted: 09-09-2020 01:03 am
  PM Quote Reply
2nd Post
gvictora
Member
 

Joined: 06-23-2020
Location:  
Posts: 4
Status: 
Offline
Well, I don't know why but after fiddling with a lot of wires and also directly jumping power to the starter from the battery, everything is now fine. I won't go through the whole process, but I think maybe my starter is getting weak and it just picked a bad time to not engage. I hope the wiring was never affected. I guess I'll only know with time. For now she starts every time.

Back To Top PM Quote Reply

 Posted: 09-09-2020 08:25 am
  PM Quote Reply
3rd Post
subwoofer
Member
 

Joined: 04-01-2008
Location: Sandefjord, Norway
Posts: 617
Status: 
Offline
Welcome to the crazy world of Lucas Electrics. Gremlins everywhere.

One of the major problems of the wiring harness is that high load circuits go through actual switchgear rather than relays, contact surfaces in the switches then go bad with use over time. Adding a relay to the solenoid circuit and switching the starter for a modern geared type will prevent later problems.

--
Joachim

Back To Top PM Quote Reply  

 Posted: 09-09-2020 03:15 pm
  PM Quote Reply
4th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
the main problem(over 40 years ago) was the LOGIC box(on the side wall near where your left knee would be), that wouldn't let you start it unless the seat belts were on, doors closed, etc. Shorting out the #11 wire to the #12 wire bypassed this problem(the numbers are very small and may be hard to discern at first). Also, cutting the #4 wire(purple, which is constant fused power, will eliminate the annoying buzz from the box).
This article has been discussed many times in previous threads, but I would have thought all the boxeses had been neutralized by now.
Let us know if yours had not been, as there may still be some "new" owners who have not done this fix.

Back To Top PM Quote Reply

Current time is 05:14 am  
> Jensen Healey & Jensen GT Tech > Ignition > Nothing happens in start position after working on dash wires Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems