| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| rebuilding the water pump | Rate Topic |
| Author | Post |
|---|
| Posted: 03-05-2016 08:33 pm |
|
1st Post |
|
Matthew10571 Member
|
Is there a listing somewhere on how to rebuild the water pump? I see the Delta has a rebuild kit for it, but before I start I would like to check on how to do it first. If so please post it here.
|
||||||||||||||
| |||||||||||||||
| Posted: 03-05-2016 11:32 pm |
|
2nd Post |
|
Screenplay Member
|
Hi Matthew, You might check out these links below. I thought about doing it at one time but ended up buying a rebuilt with exchange. The links are for the later, Lotus 912 engine; I'm not certain how different they are from the 907, but the housings look similar and though these aren't detailed instructions, the photos and captions might give you a better idea if you would like to pusrsue a rebuild on your own. You'll of course need a press and I've heard (and read) about aluminum housings getting cracked in the process. Best of luck. Clinton http://www.lotustalk.com/forums/f164/91-se-water-pump-rebuild-instructions-112632/ http://picasaweb.google.com/lotusse http://www.lotusmarques.com/parts/catalogue/news/995-lotus-esprit-water-pump-options
|
|||||||||||||
| ||||||||||||||
| Posted: 05-28-2016 02:34 pm |
|
3rd Post |
|
Joenpate56 Member
|
Clinton I think my water pump is leaking so Iam going to replace it. What is the best source for a rebuilt pump. Do you know if there are step by step instructions for the pump removal Thanks Dick
|
||||||||||||||
| |||||||||||||||
| Posted: 05-29-2016 11:24 pm |
|
4th Post |
|
dwalls1 Member
|
Club Store was a good source for mine, some years back and still functioning fine.
|
|||||||||||||
| ||||||||||||||
| Posted: 05-30-2016 06:38 am |
|
5th Post |
|
subwoofer Member
|
Lotusbits in the UK has brand new water pumps. -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 05-30-2016 01:53 pm |
|
6th Post |
|
Brett Gibson JH5 20497 Member
|
Bruce Madden "The red Racer" in GA rebuilds them Last edited on 05-30-2016 01:53 pm by Brett Gibson JH5 20497 |
|||||||||||||
| ||||||||||||||
| Posted: 06-06-2016 02:08 am |
|
7th Post |
|
dbeliveau74 Member 
|
Club Store has a re-manufactured one for $199.00 exchange that sounds pretty good! JMHO! Even comes with new SS bolts and 1 allen head to clear that troublesom pulley!! Dan Last edited on 07-02-2017 02:28 am by dbeliveau74 |
||||||||||||||
| |||||||||||||||
| Posted: 06-06-2016 01:53 pm |
|
8th Post |
|
Brett Gibson JH5 20497 Member
|
You can buy the bearing for $13.10 and the seal for $10.80 from JAE and do it yourself, they even have a tool to set everything for around $35, that way you can go into the re-build business yourself. A new impeller cost about $40 but most of the time you can re-use your old one, or better yet get a 910 impeller rather than the 907 and increase your water volume flow and keep the engine running cooler. (some machining is required to use a 910). Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 06-27-2016 08:55 pm |
|
9th Post |
|
redracer Member
|
I still rebuild them, although I am running out of good cores. Please email me at RedRacerbm@gmail.com or call at 404-261-2552 if you like. bruce madden
|
||||||||||||||
| |||||||||||||||
| Posted: 08-01-2016 02:43 am |
|
10th Post |
|
Esprit2 Member
|
Brett Gibson JH5 20497 wrote:(Snip)... A new impeller cost about $40 but most of the time you can re-use your old one, or better yet get a 910 impeller rather than the 907 and increase your water volume flow and keep the engine running cooler. (some machining is required to use a 910).Place a J-H and a 910 impeller side by side on the table, and you'll easily see that the 910 impeller is taller. It will not fit into the J-H pump housing. Take both impellers to a machine shop and have the 910's center boss / snout shortened to match the J-H impeller's overall height. It will then fit in the housing, and the rest of the assembly steps are as standard. Early 910 impellers had a 1/2" bore(same as the J-H), while later ones have a 12mm bore. Either one will work in your J-H pump housing (once machined to fit), you just have to buy the bearing with the matching impeller shaft diameter. Regards, Tim Engel
|
|||||||||||||
| ||||||||||||||
| Posted: 08-01-2016 03:43 am |
|
11th Post |
|
Esprit2 Member
|
Brett Gibson JH5 20497 wrote:You can buy the bearing for $13.10 and the seal for $10.80 from JAE and do it yourself, they even have a tool to set everything for around $35, (Snip)...JAE sells a seal with an all steel body (no rubber coating), and a sleeve that is a light press fit on the bearing's shaft. The installation tool simultaneously presses the body and the sleeve in to different depths. The seal can be installed without the tool if you know what you're doing, but it's a pain. Just use the tool and the job is a slam dunk. Some other Lotus specialists sell a seal with an outer rubber skin, and (more importantly) no sleeve to press onto the shaft. They can be installed with any appropriate pusher (a deep well 1/2" drive socket), and the installation tool discussed above does not apply. Regards, Tim Engel
|
||||||||||||||
| |||||||||||||||
| Posted: 08-02-2016 04:08 pm |
|
12th Post |
|
redracer Member
|
Richard: don't know if you've solved your water pump leak yet, but the 3G seals Tim refers to are the way to go. You will need a press regardless, but assuming whoever rebuilds it please be sure they use the 3G(the seal is totally encased in a metal housing). As for the nose of whatever impeller you use, you can grind it off in a grinder as the nose no longer is necessary to push the type 1G & 2G seals down. (a machine shop would likely have a minimum $50 set up charge/minimum. I use a large carbide surface bit in a drill press). Just be sure you grind off enough to allow the 0.020"-0.030" of clearance so you don't get cavitation. This should last "forever", asssuming you don't over tension the fan belt(adjust when engine is hot)
|
|||||||||||||
| ||||||||||||||
| Current time is 08:29 am | |
| > Jensen Healey & Jensen GT Tech > Cooling > rebuilding the water pump | Top |
