Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Steering binding  Rating:  Rating
AuthorPost
 Posted: 09-19-2011 12:45 am
  PM Quote Reply
1st Post
Mason Jones
Member


Joined: 06-03-2011
Location: Austin, Texas USA
Posts: 97
Status: 
Offline
Soooo…the steering has been binding lately. Not sure when it started. It binds at certain points in the turning radius, not consistently. I had the steering shaft out while replacing the exhaust manifold but it was not binding immediately afterward.

I loosened the bottom u-joint and discovered that it only moves in one direction. Is this normal? Seems contrary to the idea of a universal joint. Moves fine one way but won’t budge the other. This would explain the binding but before I try to unstick it I wanted to make sure that it was not the way it was designed.

This video illustrates how it moves (or doesn’t move). Normal or FUBAR?
http://youtu.be/NpranxKa3EY

Back To Top PM Quote Reply  

 Posted: 09-19-2011 03:45 am
  PM Quote Reply
2nd Post
JodyKerr
Member


Joined: 05-15-2006
Location: Tempe, Arizona USA
Posts: 217
Status: 
Offline
Mason,

 

Have someone sit in the car and turn the steering wheel while you watch the upper knuckle. It's very common for that to hit the exhaust as it rotates. Alternatively, you can get a flashlight to look at the exhaust for scratches.

What often happens is that when the exhaust is changed out the engine drops a little which causes the issue. To fix it you need to raide the engine a hair on it's motor mount until it no longer hits.

I start with that and if that's not the issue look more deeply at the steering.

Back To Top PM Quote Reply

 Posted: 09-19-2011 04:44 am
  PM Quote Reply
3rd Post
Mason Jones
Member


Joined: 06-03-2011
Location: Austin, Texas USA
Posts: 97
Status: 
Offline
Hey Jody,

Thanks for the quick response! I actually did check the upper and lower joints (had my 6-yr-old turn the wheel) and they were not hitting anything.

That's when I took a closer look at the lower u-joint and discovered it doesn't move both ways, only one. I can't imagine this is normal but wanted to ask as I've been wrong before! Not sure if I'm describing it properly--hence the video.

What would make the u-joint suddenly seize up one way? Is it fixable? Can you take them apart?

Thanks,
Mason

Back To Top PM Quote Reply  

 Posted: 09-19-2011 07:08 am
  PM Quote Reply
4th Post
JodyKerr
Member


Joined: 05-15-2006
Location: Tempe, Arizona USA
Posts: 217
Status: 
Offline
ok. I watched the video. That doesn't look right to me. I'm afraid I'm in the middle of my TR8 at the moment (literally) so I don't have easy access to the JH. The TR8 has almost the exact same assembly as the JH though, and mine happens to be loose as I'm doing a remove and replace on the power steering.

I just checked the 8 and it's got a full range of motion. I'd try setting the end in a vice and seeing if you can work it loose a bit. If not you'll likely have to get one of the refurb units from Delta.

Jody

Back To Top PM Quote Reply

 Posted: 09-20-2011 07:42 pm
  PM Quote Reply
5th Post
Mason Jones
Member


Joined: 06-03-2011
Location: Austin, Texas USA
Posts: 97
Status: 
Offline
Thanks Jody, seems like most of my questions are of the “Hey, does this look right?” variety. I was half expecting someone to chime in with, “What you’ve got there is a Lucas ‘one-way’ U-joint used only in JH #’s 11666, 12666 and 13666 designed to be driven exclusively in traffic circles.”

I just priced a new one from Delta: $85, ouch!

Back To Top PM Quote Reply  

 Posted: 09-26-2011 03:54 am
  PM Quote Reply
6th Post
Arvin Appelman
Member
 

Joined: 03-14-2005
Location: Columbia, Tennessee USA
Posts: 50
Status: 
Offline
Put it in a vice with the steering shaft in place with the lock bolt tight, try to break it loose. If it frees up fine if not order a new one.

Back To Top PM Quote Reply

 Posted: 09-26-2011 04:41 pm
  PM Quote Reply
7th Post
Mason Jones
Member


Joined: 06-03-2011
Location: Austin, Texas USA
Posts: 97
Status: 
Offline
I ordered a new u-joint from Delta. I was able to move the old joint with a lot of effort (and a hammer) but it never loosened up.

I ordered the lower steering column bushing as well. The lower column shaft has about 1/2" of play!! That can't be good.

So, this month's JH budget went to the steering, a worthy cause. I'm anxious to see what it feels like back on the road.

Back To Top PM Quote Reply  

 Posted: 10-01-2011 10:00 am
  PM Quote Reply
8th Post
Mason Jones
Member


Joined: 06-03-2011
Location: Austin, Texas USA
Posts: 97
Status: 
Offline
Slight setback on the steering, the u-joint I got from Delta was flawed. The splines didn’t line up properly with the notch in the shaft for the pinch bolt so the bolt would not go in all the way. Called Delta and as luck would have it that was the last one in stock. New ones are on order.

In the meantime I couldn’t resist taking it around the block. Steering feels great. I’m not going to say it feels like a new car because every time I say that some other major system fails to remind me this is a 38 year-old car.

Back To Top PM Quote Reply

 Posted: 10-01-2011 02:10 pm
  PM Quote Reply
9th Post
JodyKerr
Member


Joined: 05-15-2006
Location: Tempe, Arizona USA
Posts: 217
Status: 
Offline
Bummer on the steering knuckle.

 

Good for the driving though! I love the feeling in the car when something's been improved.

Back To Top PM Quote Reply  

 Posted: 10-01-2011 03:58 pm
  PM Quote Reply
10th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Frank Schwartz might have a spare available, I just helped him strip a couple of cars and one of the items I took off was a steering shaft along with good u-joints.
If your intrested he's on this board and you can ask him.

Brett

Back To Top PM Quote Reply

 Posted: 10-01-2011 08:14 pm
  PM Quote Reply
11th Post
Dakota123
Member
 

Joined: 03-20-2009
Location: Colorado USA
Posts: 187
Status: 
Offline
I just did this as well and getting the flat to line up was a pain. I dinged the bolt threads to the point where I needed to replace the bolt first time around -- is it close enough that a little filing of the flat (or maybe file a slight flat in the bolt, chase the threads) would work?

Mike

Back To Top PM Quote Reply  

 Posted: 10-03-2011 06:03 am
  PM Quote Reply
12th Post
Mason Jones
Member


Joined: 06-03-2011
Location: Austin, Texas USA
Posts: 97
Status: 
Offline
Dakota123 wrote:  -- is it close enough that a little filing of the flat (or maybe file a slight flat in the bolt, chase the threads) would work?

I guess I don't want to grind the shaft because of a faulty u-joint especially since I paid $85 for it! If I ever need to replace the upper with the shaft I'll be grinding the new shaft too.

Since you had the same problem now I'm wondering what my chances are with the next batch they get from their supplier in Britain.

Maybe a used one is not a bad idea. I'll hit up Frank...

Back To Top PM Quote Reply

Current time is 05:31 pm  
> Jensen Healey & Jensen GT Tech > Suspension > Steering binding Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems