Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Suspension > Upper control arm bolt and subframe

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Upper control arm bolt and subframe  Rate Topic 
AuthorPost
 Posted: 03-03-2009 12:15 am
  PM Quote Reply
1st Post
Gary Martin JH 15371
Member
 

Joined: 03-12-2005
Location: Portland, OR
Posts: 98
Status: 
Offline
My left front upper control arm is loose. I had thought the bushings were worn out. I just removed the long mounting bolt and removed the control arm. The bushings are intact. The problem is that the long bolt is worn and is loose in the tube that goes through the cross member. I have another bolt that is less worn, but it is still loose in the cross member tube. It looks to me like the tube in the cross member is worn. Has anyone run into this problem, and how can it be fixed?

Gary

Back To Top PM Quote Reply  

 Posted: 03-03-2009 10:38 pm
  PM Quote Reply
2nd Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
New bushings come with those tubes, not sure if you can get them by them selves, might try a bearing warehouse in your neck of the woods. Good luck

Back To Top PM Quote Reply

 Posted: 03-04-2009 06:10 am
  PM Quote Reply
3rd Post
subwoofer
Member
 

Joined: 04-01-2008
Location: Sandefjord, Norway
Posts: 617
Status: 
Offline
I thought the crush tubes actually carried the load, not so much the bolt? When you torque down the mounting bolt, the crush tube is put under compression, and is held in place by that. If it is worn by the bolt rattling about, that would mean that the bolt wasn't properly tightened in the first place, right?

--
Joachim

Back To Top PM Quote Reply  

 Posted: 03-05-2009 02:44 am
  PM Quote Reply
4th Post
Gary Martin JH 15371
Member
 

Joined: 03-12-2005
Location: Portland, OR
Posts: 98
Status: 
Offline
Joachim,

Good point. Previous owner may not have tightened the upper control arm bolt enough, or it came loose over the years. I will tighten some more and see if this helps. But it seems to me that the bolt should fit fairly snug in the crush tube through the sub frame. Without the control arm mounted, if I just place the bolt in the tube it is loose by about .010 in. This translates into about 0.25 in movement out by the upper ball joint with control arm mounted.

The Jensen manual does not mention anything about bushings in the tube through the sub frame. The tube does not look thick enough to ream out and re-bush it. So short of repalcing the whole sub frame, I'm trying to figure out my options. A brand new bolt may help, but not sure if I can find a high grade one that size. I think I need to devise some way to take some thin wall steel tubing and try to shim the slack between the bolt and the tube. Gary

Back To Top PM Quote Reply

 Posted: 03-05-2009 03:10 pm
  PM Quote Reply
5th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Gary, the bolts can be had along with lock nuts in high tensil, Delta did have them but I ended up getting them from a Bolt place on line, much cheaper, they were not fine thread but that didnt make any differance, had them on all last seasons along with replacement bolts on the rest of the suspension with no issues, without running out to the garage to check the spares I think they were 9 or 9.5" long, grade 8.

Plus the tubes that are welded to the frame assembly go along way in helping keep out play, personnally I would stay away from shimming never had to good a luck with that, worse case I think I would prefer boring out and going the next size bolt dia. up.

Brett

Back To Top PM Quote Reply  

Current time is 04:24 pm  
> Jensen Healey & Jensen GT Tech > Suspension > Upper control arm bolt and subframe Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems