Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Hazard Lights  Rating:  Rating
AuthorPost
 Posted: 11-01-2010 02:45 am
  PM Quote Reply
1st Post
RG
Member
 

Joined: 09-27-2010
Location: Troy, New York USA
Posts: 13
Status: 
Offline
I just bought a 1973, vin 13934 and set about preparing for a NY Inspection. The Hazard Light Switch had come apart so I replaced it with a good take-out from a 74 parts car. Even with the new switch the Hazards were still inoperative. I found that I did not have power to the switch. The 74's owner's manual noted that power for the hazards was supplied through a 25 amp fuse located under the dash. I searched and was unable to locate the fuse.

Is this the same on a 73?

Is this fuse an inline glass bus fuse or a fusable link? Or are the Hazards fused from the main (3) fuse block?

I am able to get the Hazards to work if I toggle the Hazard Switch on and activate the turn signal stalk to either position. I assume the power from the turn signals are back feeding the Hazards.

Thanks,

Rob

Back To Top PM Quote Reply  

 Posted: 11-01-2010 07:11 pm
  PM Quote Reply
2nd Post
MikeIsotech
Member


Joined: 04-22-2010
Location: Winchester, United Kingdom
Posts: 33
Status: 
Offline
Hi Rob

I'm currently putting my Healey back together and got the hazzard lights working only last week. You should have power to the switch - if not I'd look again for the in-line 25A fuse and check it. My car is a righthand drive and the fuse is built into the wiring loom. It's under the dash, quite close to the wiper motor.

There's some wiring diagrams on line which I've found really useful: http://home.comcast.net/~jrkengr2/html/wiring_diagrams.html

Good luck!

Mike

Back To Top PM Quote Reply

 Posted: 11-02-2010 01:25 am
  PM Quote Reply
3rd Post
RG
Member
 

Joined: 09-27-2010
Location: Troy, New York USA
Posts: 13
Status: 
Offline
Mike,

Thanks for the link....the wiring diagrams and under-dash pics were a big help.

Rob

Back To Top PM Quote Reply  

 Posted: 11-03-2010 11:29 am
  PM Quote Reply
4th Post
RG
Member
 

Joined: 09-27-2010
Location: Troy, New York USA
Posts: 13
Status: 
Offline
Found the fuse and it was okay. The Hazards will only work with the "Hazard Toggle" in the on position and the "Turn Signal Stalk Switch" in either position. They will not work only with Hazard Toggle on.

Anyone have a fix?


Thanks in advance.....Rob

Back To Top PM Quote Reply

 Posted: 11-03-2010 02:08 pm
  PM Quote Reply
5th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Do the turn signals work ???, the hazard switch when turned on bypass's the turn signals and they should flash even if the key is not turned on, there should be constant power to the switch at all times, are the two flasher units mounted under the dash  on the side wall any good. You really need to trace the power feed to the switch to see were you are losing it.

Most connections under the dash are usually in pretty good condition, unless someone has ducked with them, alot of the troubles come from the engine bay were the wires can get corroded, brittle fraded etc, clean your grounds, check the harness infront of the radiator and clean it up, I have seen bad connections there affect the flashers even though the turn signal worked. It really comes down to making sure you have good contacts which takes time and patience.

Brett

Back To Top PM Quote Reply  

 Posted: 11-03-2010 04:31 pm
  PM Quote Reply
6th Post
MikeIsotech
Member


Joined: 04-22-2010
Location: Winchester, United Kingdom
Posts: 33
Status: 
Offline
Brett is right, the normal turn circuit should be isolated when the hazard switch is on. I'm wondering if you have problems with your new switch. I had to take mine apart and clean up the switch faces as they had oxidized with age.

One easy way to check out the hazard operation is to do it without the switch. Take the switch off the connector and use a small piece of wire to link between pin 3(light-green & pink wire) and pin 1 (green & white wire) on the harness connector. That will hardwire the power to the hazard side of the circuit and remove the normal turn signal side. You should now have the hazard lights working. If they aren't it may be worth trying a new hazard unit. If they are working then you need to check out the switch.

I decided to replace my old hazard and flasher units with modern electronic parts. The old electro-mechanical units are sensitive to the current flowing so don't always flash. The electronic ones are much more reliable. I got them for around $6 each and only had to add a ground wire to make each work.

Hope it helps

Mike

Back To Top PM Quote Reply

 Posted: 11-03-2010 04:47 pm
  PM Quote Reply
7th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
As a note, the new Lucas flasher units in my own experience are basically crap, they are a mass produced cheap product. I ended up using the old ones after cleaning them up. If you really have to replace them go to a Auto store and try and get a good quality unit even if it's a three prong unit they will still work. FYI.

Brett

Back To Top PM Quote Reply  

 Posted: 11-03-2010 07:03 pm
  PM Quote Reply
8th Post
MikeIsotech
Member


Joined: 04-22-2010
Location: Winchester, United Kingdom
Posts: 33
Status: 
Offline
The electronic one's are great - they have a proper timer inside and they so they flash at the same rate no matter what current is flowing. They fit in the same place in the harness as the original electro-mechanical units but have one extra terminal which is connected to the chassis. I linked it to the mounting screw and it worked beautifully. What was strange is that they were cheaper here in the UK than new electro-mechanical devices. A no-brainer for me: cheaper and more reliable = perfect

Back To Top PM Quote Reply

 Posted: 04-03-2015 07:25 pm
  PM Quote Reply
9th Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
I have a late 74 JH and had to fix the hazard switch. I reviewed the nice wiring diagrams by John Kimbrough and the comments in this thread. As far as I know, my car is all original, but the connections are a bit different from what has been described. Just as an FYI, on my car pins 5 and 6 power the regular turn signal circuit (switched by the ignition key), with 5 being the hot side. On the hazard circuit, pin 1 is always hot (not switched by ignition), with pin 2 powering the right flasher, and pin 4 powering the left flasher.

Eric

Back To Top PM Quote Reply  

 Posted: 04-04-2015 03:07 am
  PM Quote Reply
10th Post
Screenplay
Member
 

Joined: 07-12-2013
Location: San Francisco, California USA
Posts: 124
Status: 
Offline
Eric,
Just a quick note regarding wiring. I can't offer anything specifically about the hazard switch wires, but I have mysteries regarding other wiring on my late '74 (19450). Trunk wiring (fuel pump, sending unit) look nothing like the wiring for any JH I can find. I have an earlier '74 (18059) that matches perfectly to existing diagrams, but the late one doesn't match anything I've found including diagrams for the GT. Interestingly, the tank sending unit wire is extremely long, but the wrong color for GT specs. There are even some light purple wires that are stubbed off near the fuel pump for what purpose I don't know. I posted on this a few months back but no satisfying responses were returned. It is, almost without doubt, unmodified from original but still... Were there some cars built with wiring looms not documented?
Clinton

Back To Top PM Quote Reply

 Posted: 04-04-2015 04:05 am
  PM Quote Reply
11th Post
Eric
Member
 

Joined: 11-11-2014
Location:  
Posts: 35
Status: 
Offline
Clinton,
Thanks for the info. I'm glad I'm not the only one with weird wiring! I'll take another look at my fuel pump, but I do recall seeing more wires than you'd expect there. I thought I had better post my experience just in case some other poor soul out there was as perplexed as I was trying to figure out why my wiring was so different from what had been described! Maybe near the end of production, with money running out, the factory got some wiring harnesses originally made for some other purpose and modified them to fit in the JH. Never a dull moment with this car.

Eric

Back To Top PM Quote Reply  

 Posted: 04-04-2015 03:13 pm
  PM Quote Reply
12th Post
gmgiltd
Member
 

Joined: 07-10-2012
Location: Whitehills , United Kingdom
Posts: 168
Status: 
Offline
A few possibilities for the extra wires in the trunk of a JH as opposed to a GT.
Rear screen heater
Rear window washer pump
Rear wiper
Switch for the interior light from the hatch - I don't know if the JH had a trunk light or not.
In addition to that I believe that legislation was in progress regarding rear fog lights which can only be switched on when the headlights are on - and should be extinguished when the headlights are switched off. If this was the case I would imagine it would be much easier to add a few wires to the loom rather than having to retrospectively fit them.
Gordon

Last edited on 04-04-2015 03:17 pm by gmgiltd

Back To Top PM Quote Reply

 Posted: 04-07-2015 06:02 pm
  PM Quote Reply
13th Post
Screenplay
Member
 

Joined: 07-12-2013
Location: San Francisco, California USA
Posts: 124
Status: 
Offline
Gordon, Thanks for suggesting the possibilities. I thought about those GT items but none of the colors from the GT diagram match - not even close (from memory so I don't recall the actual colors). Friends (who are not JH owners) immediately brought up what Eric mentioned: end of production financial woes. It would be great to get the definitive answer to this type of question as it was only 40 years ago.
Clinton

Back To Top PM Quote Reply  

Current time is 06:44 pm  
> Jensen Healey & Jensen GT Tech > Electrical & Instruments > Hazard Lights Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems