| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| J-H Dash Removal and Wiring | Rate Topic |
| Author | Post |
|---|
| Posted: 08-27-2010 04:06 am |
|
1st Post |
|
mojo-09 Member
|
I am looking for directions for removal of the dash to get to the bulb for bright light indicator. Also looking for a good wiring diagram that has pictures of the starter, alternator & etc. Thanks Jim My email address is j_alively@mcloudteleco.com
|
||||||||||||||
| |||||||||||||||
| Posted: 08-27-2010 01:51 pm |
|
2nd Post |
|
Brett Gibson JH5 20497 Member
|
Jim, there are two screws one in each corner of the upper dash pod, then the pod is resting on a shaft, depending on if the shaft was lubed or not it just slides out forward untill the speedo cable and oil line restrict it's movement, you might be able to reach around and get at the high beam light from there. If not disconnect the speedo cable at the back of the odometer, disconnect the oil line on the engine block, or behind the gauge, sometimes not to easy. As for a wiring Dia. they are out there on the Web, British steel, or John Kimbrough has a web page in the links portion of this site. Good luck Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 08-27-2010 03:37 pm |
|
3rd Post |
|
JodyKerr Member 
|
Do as Brett said in the first response. I've found that the posts almost always stick from lack of lubrication over the years. I normally hit them with steel wool and a little penetrating oil. Also, it's much easier to fiddle with it on the bench. Remove the speedo cable (as mentioned) and the oil line. When you remove the oil line zip tie or tape a bag over the end. If you don't it's guaranteed to leak oil into your interior. You'll also have to disconnect the two main wirhing harness connections (1 black, 1 white if your wiring is still correct). While you're in there I'd recommend changing out all the bulbs at once. Jim @ Delta Motorsports found a better bulb a year or so ago, they're much brighter. I'd get those bulbs, they make a huge difference. The wiring that connects the bulbs is very thin. Go slowly and carfully. If you're ham fisted in there you'll be accidentally squishing the sockets or ripping them from the harness. Also, a lot of the bulbs ground to the bulb socket. Clean up all those connections and apply a little dielectic grease to them. It helps on reassembly as well as keeps them gack free if you need to go in there again. Jody
|
||||||||||||||
| |||||||||||||||
| Posted: 08-27-2010 07:16 pm |
|
4th Post |
|
subwoofer Member
|
If the pod is stuck, grab a crowbar and assume the Lotus position. Push on the end of the steel rod sticking out the back of the instrument with the crowbar, using the steering column brackets for leverage. Worked a charm for me, and that rod was badly rusted. -- Joachim
|
|||||||||||||
| ||||||||||||||
| Posted: 08-27-2010 07:54 pm |
|
5th Post |
|
mojo-09 Member
|
Thanks for the information it is a big,big Help. Thanks Jim
|
||||||||||||||
| |||||||||||||||
| Posted: 08-27-2010 07:57 pm |
|
6th Post |
|
mojo-09 Member
|
Thanks for the information it is a big, big Help. I just ordered a box of the bulbs from them, hope they are the ones you are talking about. Thanks Jim
|
|||||||||||||
| ||||||||||||||
| Posted: 08-27-2010 10:56 pm |
|
7th Post |
|
mojo-09 Member
|
Their were two screws at each end of dash. But their seems to be somethings else holding the dash in. Also do i need to take the center console out and the steering wheel off. You said one screw at each end maybe i took the wrong screw out but they looked like the bracket were atched to the dash. Also where do you take hold of the dash to work it loose? Thanks Jim
|
||||||||||||||
| |||||||||||||||
| Posted: 08-28-2010 12:18 am |
|
8th Post |
|
JodyKerr Member
|
You don't have to take out the whole dash, just the instrument cluster. at both sides of the cluster inset into the black molded unit are two screws. Those are what we were referring to. If you got those, you should be able to sliglty lever both sides, but the center pin is still holding it in place.
|
|||||||||||||
| ||||||||||||||
| Posted: 08-28-2010 07:17 pm |
|
9th Post |
|
John Finch Member
|
Attached is a pix of the pod removed. You can see the rusty rod in the center. Hope this helps. Attachment: new_dash_lights.jpg (Downloaded 223 times)
|
||||||||||||||
| |||||||||||||||
| Current time is 06:16 am | |
| > Jensen Healey & Jensen GT Tech > Electrical & Instruments > J-H Dash Removal and Wiring | Top |
