Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
BRAKE FLUID  Rate Topic 
AuthorPost
 Posted: 06-08-2007 05:43 am
  PM Quote Reply
1st Post
timeforwalkies
Member
 

Joined: 05-24-2006
Location:  
Posts: 81
Status: 
Offline
Well it's finally together.  All the brakes stuff that is.  New front calipers, new rear cylinders and hopefully a master cylinder that dosn't leak.
Next step is bleeding.  Then adjust.
Went to my local auto parts store and picked up what appeared to be the correct stuff, but is it?  Valvoline SYN Power Full Synthetic brake fluid.  Says it exceeds DOT3 & DOT4 and good to 500 degrees F.
Anybody have an opinion about synthetic brake fluids?
Thanks,
Clif
Did a little self research, and while I am still a bit confused I have decided to take the stuff back and get DOT4.  If you are curious about why read this: http://www.xs11.com/tips/maintenance/maint1.shtml  It is everything you thought you wanted to know about brake fluids and more.  Good stuff
Clif

Last edited on 06-08-2007 06:29 am by timeforwalkies

Back To Top PM Quote Reply  

 Posted: 06-08-2007 06:13 am
  PM Quote Reply
2nd Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
I've had good luck with it.

Back To Top PM Quote Reply

 Posted: 06-08-2007 06:30 am
  PM Quote Reply
3rd Post
timeforwalkies
Member
 

Joined: 05-24-2006
Location:  
Posts: 81
Status: 
Offline
Read this. http://www.xs11.com/tips/maintenance/maint1.shtml   I am sure you are OK, but read anyway so you know why.  Thanks for the reply.

Back To Top PM Quote Reply  

 Posted: 06-08-2007 12:32 pm
  PM Quote Reply
4th Post
Jim Ketcham
Member
 

Joined: 03-13-2005
Location: Salt Point, New York USA
Posts: 208
Status: 
Offline
Valvoline SYN Power Full Synthetic is DOT 4.  It is not silicone based which is DOT 5. 

I've used it in all my cars with no problems.

 

Back To Top PM Quote Reply

 Posted: 06-08-2007 09:50 pm
  PM Quote Reply
5th Post
timeforwalkies
Member
 

Joined: 05-24-2006
Location:  
Posts: 81
Status: 
Offline
OK>>>OK
I just got off the phone with Valvoline.  They say it is the same as DOT3 and DOT4 only better.  They woudn't tell me what the synthetic is, but that is what makes it better and work for both DOT3 and DOT4 and work at higher temperatures.
They say it has no negative effects on seals, older or newer.

Back To Top PM Quote Reply  

 Posted: 09-22-2017 12:38 am
  PM Quote Reply
6th Post
Spaceman
Member


Joined: 05-30-2017
Location:  
Posts: 25
Status: 
Offline
My Jensen manual states to only use Dot 3 brake fluid, or an equivalent

Back To Top PM Quote Reply

 Posted: 09-22-2017 11:35 am
  PM Quote Reply
7th Post
gmgiltd
Member
 

Joined: 07-10-2012
Location: Whitehills , United Kingdom
Posts: 168
Status: 
Offline
Not sure if DOT 5.1 is available over there - it's fully compatible with DOT 3&4 but has a much higher boiling point. Note that DOT 5 is not compatible and will destroy your seals. Have a look at the following article.
http://www.epicbleedsolutions.com/resources/faq/difference-between-dot4-and-dot51-brake-fluid/

Gordon

Back To Top PM Quote Reply  

 Posted: 05-07-2020 03:23 am
  PM Quote Reply
8th Post
dbeliveau74
Member


Joined: 12-28-2015
Location: Manchester, New Hampshire USA
Posts: 53
Status: 
Offline
That article didn't state anything about seals and dot 5 silicone brake fluid. I have it in my JH. And the previous owner used it for 22 + years. Is there any real information about this issue?

Back To Top PM Quote Reply

 Posted: 05-07-2020 03:45 am
  PM Quote Reply
9th Post
dbeliveau74
Member


Joined: 12-28-2015
Location: Manchester, New Hampshire USA
Posts: 53
Status: 
Offline
Here is an article I found which clarifies some of the questions.
https://www.britishcarforum.com/bcf/archive/index.php/t-73218.html
Cheers,
Dan

Back To Top PM Quote Reply  

 Posted: 05-07-2020 06:01 am
  PM Quote Reply
10th Post
gmgiltd
Member
 

Joined: 07-10-2012
Location: Whitehills , United Kingdom
Posts: 168
Status: 
Offline
Hi Dan,
DOT 3,4 and 5.1 are glycol based and DOT 5 is Silicone based - glycol and silicone based fluids are not compatible with each other. In my case I upgraded the brakes to larger vented discs with 4 piston radial calipers on the front and rear discs with 2 piston calipers, but retained the original master cylinder. The braking system was previously filled with DOT 4 . The manufacturer of the discs and calipers (Hispec) advised me not to under any circumstances mix the two as the seals would be damaged -competition brake systems and road car upgrades are their core business so I would suggest that they have some experience in this field. DOT 5.1 has an even higher boiling point than DOT 5. I can't open the link you provided.
Gordon

Back To Top PM Quote Reply

Current time is 04:59 am  
> Jensen Healey & Jensen GT Tech > Brakes > BRAKE FLUID Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems