Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher Page:    1  2  Next Page Last Page  
New Topic Reply Printer Friendly
Brakes  Rate Topic 
AuthorPost
 Posted: 02-04-2017 02:07 am
  PM Quote Reply
1st Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
I engineered this setup from off the shelf calipers and rotors with working emergency brake. Designed custom mounting plates, they are bolt on but can be welded. Will weld on after testing period.

Attachment: IMG_0717.JPG (Downloaded 460 times)

Back To Top PM Quote Reply  

 Posted: 02-04-2017 04:14 am
  PM Quote Reply
2nd Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
Great !!! Tell us more......(such as..specs and drawings???)

Frank

Back To Top PM Quote Reply

 Posted: 02-06-2017 01:16 pm
  PM Quote Reply
3rd Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Working on providing details

Back To Top PM Quote Reply  

 Posted: 02-20-2017 02:52 am
  PM Quote Reply
4th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Working with a supplier who will make laser cut brackets, you can order direct from them. Installation document will be done soon. Hang in there!

Back To Top PM Quote Reply

 Posted: 02-24-2017 09:47 pm
  PM Quote Reply
5th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Awesome stuff! Please advise on caliper and disk used. Been looking at this modification for quite some time but looks like you found a disk rotor with 4 x 4.00" bolt circle and a usable offset, bravo. Counter sink the lug holes and use conical seat lug nuts to center disk and then I'd drill in four counter sinks and tapped holes in the flange to assure it stays on center or perhaps design up a light press-fit bushing to center it on the axle shaft boss.

Back To Top PM Quote Reply  

 Posted: 03-17-2017 04:48 am
  PM Quote Reply
6th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
I finished may assembly guide what use and did, also received a quote from a laser cut source. Only leaves me with getting samples of their parts to make sure they fit. The rotors are on 100mm bolt circle, however their clearance hole is large enough for exact fit to outside edges of lug studs to center rotor on hub plate. I test drove a lot and everything performs well. The pedal pressure is stiffer. I also included a rear proportion valve,

Back To Top PM Quote Reply

 Posted: 03-17-2017 04:58 am
  PM Quote Reply
7th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
Wonderful !! A really nice addition to the JH...looking forward to the "whole package" of parts list and laser cut parts..

Back To Top PM Quote Reply  

 Posted: 03-20-2017 12:03 am
  PM Quote Reply
8th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Thanks for everyone's interest in rear disc. I Will talk with the laser cut supplier monday, should have everything together this week to release PDF on installing rear disc brakes.

Back To Top PM Quote Reply

 Posted: 03-22-2017 11:53 pm
  PM Quote Reply
9th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
I have a PDF on how I did my rear brake conversion. Send a request to me at: 07vette47@gmail.com
I'll email you a copy.

Back To Top PM Quote Reply  

 Posted: 03-29-2017 02:42 am
  PM Quote Reply
10th Post
t4brew
Member
 

Joined: 03-11-2010
Location:  
Posts: 12
Status: 
Offline
Great work!

I have been looking into possible brake upgrade solutions also and have some prototypes for front and rear brakes using Honda/Acura calipers with various rotors. I also came up with a prototype for some Wilwood calipers. My problem had been lack of time to move from prototype to production.

I have some pictures at:

http://www.jhppg.com/mediagallery/album.php?aid=516&page=1

I created a brake upgrade pdf here:

http://www.jhppg.com/mediagallery/album.php?aid=475&sort=0

Maybe this can help other people looking into how to upgrade your Jensen Healey brakes.

If people are interested I can post more details about the caliper adapter brackets.

Back To Top PM Quote Reply

 Posted: 04-03-2017 03:23 am
  PM Quote Reply
11th Post
Bluekaos5
Member
 

Joined: 03-14-2017
Location: Chilliwack, British Columbia Canada
Posts: 8
Status: 
Offline
HiSpec Motorsports in England has posted a new single piston rear caliper with an electric e-brake which they say will be available summer 2017. At 770 GBP for calipers, ECU and wiring cables; its a bit pricey but this would definitely cut out a lot of headaches engineering and fabricating e-brake linkage/cable.

http://www.hispecmotorsport.co.uk/electronic.html

Last edited on 04-03-2017 03:27 am by Bluekaos5

Back To Top PM Quote Reply  

 Posted: 05-15-2017 01:11 am
  PM Quote Reply
12th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Honda CRX brakes work with the Honda OEM emergency brake cables. I pitched the stock JH cable and rod as it doesn't really work on floating disk brake calipers.

The 1/4" thick caliper mounting bracket welded to the axle sets a perpendicular line that is through the caliper fixing holes at 45° to the horizontal. So the angle is a bit steeper than Jomac's installation but this allows for better bleeding of the air from the caliper. Albeit the proximity to the shock is a bit closer than I would like but it does clear well enough.

This angle also allows the parking brake cables to clear the frame and radius arms as they pass around the coil springs at ride height.

Also the added height of the caliper allows the Centic brand banjo bolted brake line to bend to a nut I welded to the radius arm to fix the tab for the lines routing to a tee that is yet to be procured and mounted on the diff-housing.

Attachment: WP_20170513_002.jpg (Downloaded 241 times)

Last edited on 01-26-2022 03:50 am by atgparker

Back To Top PM Quote Reply

 Posted: 05-15-2017 01:14 am
  PM Quote Reply
13th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
CRX OEM Brake cable bracket fabricated from some 1.00" wide steel strip, a wave washer flat washer and E-clip retaining ring.

Attachment: WP_20170513_004.jpg (Downloaded 240 times)

Back To Top PM Quote Reply  

 Posted: 05-15-2017 01:44 am
  PM Quote Reply
14th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Emergency Brake Cable Management using the OEM CRX cables. note the upper control arm bolt is utilized for the bracket fixing. The cables come with three bent up retainers two are located on steel keepers that allow the axial location of the cable to be controlled.

I cross the cables to open up the bend radius so the passenger side cable at the caliper enters the driverside of the tranny tunnel and vice versa for the driver side cable.

Attachment: WP_20170514_001.jpg (Downloaded 239 times)

Last edited on 05-15-2017 02:06 am by atgparker

Back To Top PM Quote Reply

 Posted: 05-15-2017 01:44 am
  PM Quote Reply
15th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Twin Cable to Handbrake lever modification. All thread passes back through OEM cable hole with plastic tubing slipped over the all thread to keep rattles to a minimum.

The OEM JH header plate is replaced with a new one I fabricated from the same .190 x 1.00 steel strip. It has three 1/2" holes and two to allow the OEM screws to fix it to the unibody.

The CRX cable housing ends are close to 1/2 inch OD and are set 4" apart on center with the cables original hole so that the offset in the tranny tunnel is maintained. Its slightly to the left of center or nearer to the drivers side.

I had to add a swivel pivot to allow for cable length miss-match to equalize. It is made of some 7/8 OD aluminum rod with a 3/8 hole drilled through for the all tread to pass through with a bushing to ride against it. This keeps the slot in the square steel tube to a minimum to allow the bar to yaw as the cables are not the same length when you remove the slack.

Attachment: WP_20170526_004.jpg (Downloaded 204 times)

Last edited on 01-27-2022 09:57 pm by atgparker

Back To Top PM Quote Reply  

 Posted: 05-15-2017 02:04 am
  PM Quote Reply
16th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Cable routing from caliper to pivot axis of upper control arm bolt. It was like these cables were made for the car.
Note the rubber bonger on this section of the cable at mid span between the frame and radius arm.

Attachment: WP_20170513_003.jpg (Downloaded 237 times)

Last edited on 05-15-2017 02:26 am by atgparker

Back To Top PM Quote Reply

 Posted: 05-15-2017 02:38 am
  PM Quote Reply
17th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Header plate used to secure cable outer housing in the tranny tunnel.
Those stepped sheet metal hole-saw's are the ticket for popping in the new holes in the cars sheet metal.

A good drill press and some pilot hole drilling gets things close enough to make things fit.

Attachment: HEADER PLARE FOR JH USING CRX E-BRAKE CABLE.jpg (Downloaded 238 times)

Back To Top PM Quote Reply  

 Posted: 05-15-2017 02:45 am
  PM Quote Reply
18th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Adapter plate for the caliper on the axle housing.
This took three tries in thin plywood on a scroll saw to perfect for the cable angle and the hydraulic lines bend radius. Notice the piston on the caliper and the ID and OD of the swept area are included in the SolidWorks Drawing to optimize the brackets mounting hole position.

Making these out of 1/4 steel plate is no small feet and took most of a weekend to manage with basic hand tools, a saber saw and a 4 inch disk grinder.

PM me for pdf's of these drawings if you want to manage this approach on your Disk brake conversion.

Attachment: PLATE ADAPTER JH AXEL TO CRX CALIPER.jpg (Downloaded 240 times)

Last edited on 05-15-2017 02:51 am by atgparker

Back To Top PM Quote Reply

 Posted: 05-27-2017 04:33 am
  PM Quote Reply
19th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Hydraulic line routing to chassis

Attachment: WP_20170526_005.jpg (Downloaded 207 times)

Back To Top PM Quote Reply  

 Posted: 05-27-2017 04:40 am
  PM Quote Reply
20th Post
atgparker
Member


Joined: 06-23-2013
Location: Mission Viejo, California USA
Posts: 90
Status: 
Offline
Brackets for holding Centric Flex lines with M10 x 1.0 Thread adapters to 1/8 NPT.

All that lovely new bed liner paint on the axle needed something to set it off. Chromed hex head 1/4-28 machine screws for the differential cover!

Attachment: WP_20170526_006.jpg (Downloaded 205 times)

Last edited on 05-27-2017 04:50 am by atgparker

Back To Top PM Quote Reply

Current time is 06:26 pm Page:    1  2  Next Page Last Page    
> Jensen Healey & Jensen GT Tech > Brakes > Brakes Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems