Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Brakes > Brake Booster removal

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Brake Booster removal  Rate Topic 
AuthorPost
 Posted: 02-25-2015 05:42 pm
  PM Quote Reply
1st Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 435
Status: 
Offline
Hey everyone... as detailed in my "Project" thread, I have ordered and received a new brake master cylinder and a "slightly used" booster.  I was reading through the shop manual as to how to go about the removal of the booster, and the process there involves the disconnection of the throttle and clutch cables and removal of the pedal box.  Is that really necessary?

I assumed the Lotus position and peered up under the dash and, while it looks pretty tight, it sure looks like I can get at everything I need to under there.  I'm proposing to, from under the dash, remove the pin connecting the brake pedal to the booster clevis and then remove the 4 nuts holding the booster to the pedal box and remove it that way.  Is there a reason this wouldn't work, and how have you gone about the removal?

Back To Top PM Quote Reply  

 Posted: 02-25-2015 09:44 pm
  PM Quote Reply
2nd Post
gmgiltd
Member
 

Joined: 07-10-2012
Location: Whitehills , United Kingdom
Posts: 168
Status: 
Offline
I have done it like that - bit awkward and probably easier if you take the steering wheel off. That's on a UK spec GT but I don't imagine there would be any reason why it should not work.
Gordon

Back To Top PM Quote Reply

 Posted: 02-25-2015 10:20 pm
  PM Quote Reply
3rd Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 435
Status: 
Offline
Removing the steering wheen is the first thing I do when I know I will be spending time under the dash, so I'm good there. I need all the room I can get.

Good to know at least someone has succeeded in this method, it seems like a lot less work than removing the pedal box.

Back To Top PM Quote Reply  

 Posted: 02-26-2015 05:02 pm
  PM Quote Reply
4th Post
UKJames
Member
 

Joined: 04-24-2014
Location: Berkshire, United Kingdom
Posts: 43
Status: 
Offline
Just changed the booster on mine last year. Actually more straightforward than I thought, did it all from the engine bay.

You can unbolt the pedal box from the bulkhead quite easily, and angle the whole pedal box out, really easy access to the nuts holding the booster on, and the clevis pin then.

 

Sounds worse than it is, and no back ache...

 

 

Back To Top PM Quote Reply

 Posted: 02-26-2015 06:28 pm
  PM Quote Reply
5th Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 435
Status: 
Offline
You didn't disconnect the clutch and throttle cables?

Back To Top PM Quote Reply  

 Posted: 02-26-2015 06:44 pm
  PM Quote Reply
6th Post
UKJames
Member
 

Joined: 04-24-2014
Location: Berkshire, United Kingdom
Posts: 43
Status: 
Offline
Came out with the cables attached if I remember correctly. But once you can get at the back, its no trouble releasing the cables and the brake light wire if you wanted to put it on the bench to work on.
I was changing the master cylinder at the same time so I had a fair bit of room to pull the pedal box forward but it was straightforward, no headaches.

Back To Top PM Quote Reply

 Posted: 02-26-2015 07:04 pm
  PM Quote Reply
7th Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 435
Status: 
Offline
Ok, you're right... that doesn't sound quite as complicated as the manual made it appear. I'll take another look at it: I always prefer to work under the bonnet as opposed to under the dash, given a choice. I'll also be replacing the master cylinder at the same time so like you said space shouldn't be an issue.

Back To Top PM Quote Reply  

 Posted: 03-02-2015 08:12 am
  PM Quote Reply
8th Post
answerman
Member
 

Joined: 09-10-2012
Location: Little Chute, Wisconsin USA
Posts: 435
Status: 
Offline
Well, did all this this weekend and other than one small (ok fairly major) issue it actually went pretty well. Unfortunately because of my lack of attention, I am probably going to have to pull it out and do it all over. Hoping that someone here (maybe Greg) can shed some light and verify that I'm right before I go to all that trouble...

(There is a question at the end of this post that I do need answered... sorry about placing it there but I figured you'd want all this info first)

First of all, thanks to UKJames for the advice on pulling the pedal box. That went quite well. I got the old booster removed without too much trouble. Then, I got the new one installed on the pedal box. Here's where things get interesting....

A side note: this is the booster that I purchased "slightly used" on eBay. It's the same one Greg used to sell in the JHPS club store a few years back (using his picture). Does anyone else have one of these?  Because my question is pretty specific to this particular booster.



When I installed it into the pedal box and connected everything back up, I noticed that the brake pedal was not quite lined up with the other pedals... it was over an inch closer to the floor.  In fact, I had measured the distance from the booster face to the end of the clevis on both old and new and found about a half inch difference.  If I would have stopped there, I probably wouldn't be asking what I am about to ask.

Anyway, being impatient, I put it all back together, got the new master cylinder installed after bench bleeding it, and when I went to test things I realized my problem.  That business about the brake pedal being lower was because the clevis rod is shorter, of course... but it's so short that it's not even contacting the brake light switch, so the brake lights never turn off.  Arggh.

So, my question (after perusing the boards first).. does this particular booster have an adjustment for the length of the clevis rod?  Is it as simple as rotating it to screw it in or out?  And... though I assume I already know the answer... is it possible to adjust it while everything is installed in the car, or do I have to take it all apart again?

Last edited on 03-02-2015 08:20 am by answerman

Back To Top PM Quote Reply

 Posted: 05-04-2016 05:02 pm
  PM Quote Reply
9th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
Assuming the rebuilt one is the same as the originals, yes, there is an adjustment: if you have in back on the car, 1st remove the master cylinder to get it ot of the way of the push rod,
Next, have a friend step on the barke pedal to push the rod forward; you may notice that the end of the rod is hexed shape(5/16").
Use some vise grips at the very end of the round portion near the end end with your 5/16" socket turn(staandard right hand threads) the threaded end that goes into the round end.
CAUTION: be very careful not to use the vise grips far down the round rod or you may lose vacuum. Most of the seals there on our old boosters are hard/worn and a rebuild s called for.

Back To Top PM Quote Reply  

 Posted: 06-08-2018 08:07 pm
  PM Quote Reply
10th Post
dbeliveau74
Member


Joined: 12-28-2015
Location: Manchester, New Hampshire USA
Posts: 53
Status: 
Offline
Just attempted to remove the pedal box from US model the accelerator pedal is wrapped around the steering column. No amount of tilting or twisting will allow the pedals to come through the firewall. Any suggestions.

Back To Top PM Quote Reply

 Posted: 06-09-2018 05:40 am
  PM Quote Reply
11th Post
DonBurns
Member
 

Joined: 09-18-2015
Location: Fullerton, California USA
Posts: 148
Status: 
Offline
There are two little bolts halfway between the accelerator pedal and pedal box that need to be removed to separate the pedal. It's easy if you are a contortionist.

Back To Top PM Quote Reply  

 Posted: 06-10-2018 02:29 am
  PM Quote Reply
12th Post
dbeliveau74
Member


Joined: 12-28-2015
Location: Manchester, New Hampshire USA
Posts: 53
Status: 
Offline
Thanks Don, I see them now wow you're not kidding!!
I'll work on that first thing in the am. I'll report on the
My progress!!
Cheers

Got it!!
You weren't kidding about needingto be a contortionist!!
Needed needle nosed visegrips and a 7/16 socket to get the 2 bolts out, had togo under the dash just enough room to reach without removingthe seat and steering wheel.
A 1/2 in deep socket for the 4 lockscreen nuts to separate the booster from the pedal box.

Last edited on 06-10-2018 07:18 pm by dbeliveau74

Back To Top PM Quote Reply

 Posted: 06-11-2018 08:34 pm
  PM Quote Reply
13th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
The brake booster is fairly easy to remove without having to remove the entire pedal box assembly:
a universal and long socket along with a long extension(and maybe some kid if you don't flex much anymore) will have it off quickly, especially if one has the modern 18 or 20 volt impact wrenches so common now.
Be sure to put some "sealer" (such as Permatex #2, Hylomar or equivalent) around the interface so water won't get on your tootsies when it rains.

Back To Top PM Quote Reply  

Current time is 05:08 am  
> Jensen Healey & Jensen GT Tech > Brakes > Brake Booster removal Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems