| ||||
| ||||
| Moderated by: Greg Fletcher | Page: 1 2   |
|
|||||||||||||
| Brake upgrade? | Rating: 
|
| Author | Post |
|---|
| Posted: 09-04-2010 06:27 pm |
|
1st Post |
|
subwoofer Member
|
I haven't found a dimensioned drawing of the Girling Type 14 caliper yet, but I am guessing it is a 3,5" lug mount type. Will any of these Wilwood calipers fit? For a lug mount, is the distance from the lug mounting faces to the rear disc face standardized, or is it anyone's guess if these will fit? -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 09-05-2010 04:00 am |
|
2nd Post |
|
Art DeKneef Member
|
I doubt that any of those 3.5" calipers will fit. Based on my measurements the lug mounting points are 3.25" centered. Searching on that spacing shoes a few 2 piston calipers. They might fit. However you have to consider that the JH rotor is roughly 10" diameter and 3/16" thick. So that limits the calipers for the narrow rotor. Now consider what size rims are you planning to use? And the mount offset will vary depending on the caliper used. This has been discussed here several times in the past. Art
|
|||||||||||||
| ||||||||||||||
| Posted: 09-05-2010 07:57 am |
|
3rd Post |
|
subwoofer Member
|
I started by selecting 4-piston calipers, that's why I didn't see the 3.25" calipers. Seems Wilwood is out for now, then. I believe the rotor is 3/8", not 3/16", many calipers are available for 9.7mm rotors. Planning to run the standard wheels, possibly 13" Allycats. I remember seeing a lot about TR7 calipers, but not much in the way of performance aftermarket caliper types. HiSpec in England has a lot more for 3.25" lug mounts. -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 09-05-2010 08:57 pm |
|
4th Post |
|
Art DeKneef Member
|
My bad. I did mean 3/8" for the rotor thickness. I've heard the TR-7 calipers fit also. But have never confirmed that to be true. Amongst my notes here on front brake upgrades are stories and pictures of using: Ford ventilated rotors and calipers - unknown models numbers Saab or Volvo parts - looks close based on wrecking yard visits Outlaw brake 4-pot calipers and ventilated rotor - unknown model numbers While i am sure it has been done, I have not seen any detailed information on a successful upgrade. It's something Jody and I have discussed a few times but our priorities have been getting our cars running. I have a JH front frame and a GT front frame here that I am slowly cleaning and putting back together to use as testing points for a brake upgrade. Unfortunately it's not a high priority. Once I get a running car then I plan on spending more time on seeing what can be done. Maybe if everyone that had an interest in this shared their notes we could come up with something that could be put together with all the parts needed. Art
|
|||||||||||||
| ||||||||||||||
| Posted: 09-05-2010 09:50 pm |
|
5th Post |
|
subwoofer Member
|
I am a great believer in sharing notes. :-) Circumstantial evidence suggests that we are up against a 3.25" lug mount, and a wild guess would be that the HiSpec M14 mount will be close (could that be a reference to type 14?). It is 3.25" mount, with a 19.5mm lug-to-disc spacing and a mount height of 61.3mm. They are wide, suggesting they are made for large diameter discs. The Caterham260 mount has a lug-to-disc spacing of 18.8mm and mount height of 81mm. It is made for 260mm discs (10"3/8). That sounds awfully close, but we really need to make some measurements on the standard caliper. -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 09-06-2010 09:20 pm |
|
6th Post |
|
Art DeKneef Member
|
I have a box with some calipers from a 74 JH somewhere around here. I looked for it yesterday but could not find it. I'll check again later this week and hopefully I will find it and can get some measurements. That will be a start. Art
|
|||||||||||||
| ||||||||||||||
| Posted: 09-06-2010 11:00 pm |
|
7th Post |
|
Jensen Healey Super Moderator 
|
If you're not racing I think the stock calipers and disks with Hawk 118 or other performance street pads are a vast and suprising improvment over standard or metallic pads. Very good modulation and feel and can be locked at will. They also reduce brake fade to a minimum. What else are brakes supposed to do? The Girling type 14 caliper was also used in Formula Ford racing cars. They were much lighter than a JH but it's not like the brakes won't work. Get braided lines and replace the rear brake cylinders. Then flush the system with fresh dot 4 fluid. No issues here! Kurt
|
||||||||||||||
| |||||||||||||||
| Posted: 09-07-2010 07:24 pm |
|
8th Post |
|
Dakota123 Member
|
I fit new, not rebuilt, TR7/Spitfire Girling 16s procured from Rock Auto to 10628. Other than a different mounting bolt (the caliper mounting hole is slightly larger), and adapting to metric pipe at the caliper, it was a bolt-in. The piston is definitley larger than that of the 14s, which opens up options for increasing braking force if one works with the rest of the system (MC and booster), but as others have said pads and braided lines are probably the most important change one can make. That, and rear brakes. Mike Edit: TR7/Spitfire are Girling 16, originally typed 14. Last edited on 09-08-2010 04:46 pm by Dakota123 |
|||||||||||||
| ||||||||||||||
| Posted: 09-07-2010 10:33 pm |
|
9th Post |
|
subwoofer Member
|
Measured the caliper I had off the car today, here are the numbers: Lug distance: 82mm (3.25") Lug-to-disk: 20mm Mount height: 68mm to outer edge of piston Pad size: 60mm x 49mm I am beginning to think that the M14 mount will actually fit. Now we need to figure out a way to get a vented disc on there. Not to mention how to get rear disc brakes on there with as few machined parts as humanly possible. -- Joachim
|
||||||||||||||
| |||||||||||||||
| Posted: 09-08-2010 01:02 am |
|
10th Post |
|
Greg Fletcher Administrator 
|
This caliper is a bolt on with a spacing washers and minor mods (it's the one I was selling on the club store a while back). As one owner said to me, "it makes the JH stand on it's nose". If you really, really want to stop fast, this would be one of the least expensive ways to go about it. You would need larger wheels for this. http://www.outlawdiscbrakes.com/m16.html As Kurt points out, ceramic kevlar pads & shoes and steel brake hoses with a well functioning stock brake system do a fairly amazing job to rehabilitate 1970's stopping power on this car.
|
|||||||||||||
| ||||||||||||||
| Posted: 09-08-2010 01:10 am |
|
11th Post |
|
JodyKerr Member 
|
Hey Greg, What were the other mods involved? Jody
|
||||||||||||||
| |||||||||||||||
| Posted: 09-08-2010 05:01 am |
|
12th Post |
|
Greg Fletcher Administrator
|
You'll need to fabricate some custom rigid tubes and adaptors from the caliper to the flex hose as well as some anti rattle clips to keep the pads from making a bunch of squealing noise. I may have some tubes left if you need some.
|
|||||||||||||
| ||||||||||||||
| Posted: 07-11-2012 05:35 pm |
|
13th Post |
|
gmgiltd Member
|
Hi gents, I am a new member to the club but have had a GT since 79 which was off the road for some time. When it was re commissioned I realised just how pathetic the brakes are compared to a modern car. I took the car to HiSpec in London to be measured up and have been developing the installation up to now. Hi Spec have been advised of all the bugs and should be able to provide all the bits for front or rear standard wheel or 15". I have 15" with 22mm vented on the front and 9mm thick on the back. Front calipers are 4 pot radial mount rears are 2 pot with a cable handbrake. Gordon
|
||||||||||||||
| |||||||||||||||
| Posted: 05-20-2014 08:51 am |
|
14th Post |
|
jamescheesewright Member
|
Hi people it's been a while since I've been on this forum but I'm back working on my JH again. I'm currently focused on the brakes and in particular the front hubs. I'm going to be running an escort mark two rear axle in the healey so was wondering has anybody ever swapped to ford front hubs off say a Capri 2.8i or a mk2 escort. As this way I would be able to harmonise my wheel bolt pcd to ford 108. At the same time it would allow the vented disc bolt up from a Capri 2.8i. If anyone has the wheel bearing data for the front spindles that would be good as I can then compare it with bearings used also by ford. Also is there a separate thread on using miata mx5 tie rod ends on a JH stealing arm? To correct bump steer on a lowered JH?
|
|||||||||||||
| ||||||||||||||
| Posted: 05-20-2014 04:01 pm |
|
15th Post |
|
Jensen Healey Super Moderator
|
Hi James, The only bolt-on hub swap I know of involves Holden parts from down under. Where are you located? The Miata tie rod ends are certainly not a bolt on solution. I tried that one. They're metric for starters. Cheers, Kurt
|
||||||||||||||
| |||||||||||||||
| Posted: 05-21-2014 07:59 am |
|
16th Post |
|
gmgiltd Member
|
Hi James, There are bolt on kits from HiSpec in the UK for both 13" and 15" wheels which cost the same or less than the standard parts. Will attach some photos. Gordon Attachment: Front brake kit.jpg (Downloaded 447 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 05-21-2014 08:01 am |
|
17th Post |
|
gmgiltd Member
|
Rear Brake kit Attachment: Rear brake kit.jpg (Downloaded 436 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 05-21-2014 08:02 am |
|
18th Post |
|
gmgiltd Member
|
Front installed Attachment: Front on car.jpg (Downloaded 439 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 05-21-2014 08:06 am |
|
19th Post |
|
gmgiltd Member
|
Rear on car Attachment: Rear on car.jpg (Downloaded 437 times)
|
||||||||||||||
| |||||||||||||||
| Posted: 05-21-2014 08:07 am |
|
20th Post |
|
gmgiltd Member
|
Complete and working well. Attachment: Installed with 15 inch wheels.jpg (Downloaded 440 times)
|
|||||||||||||
| ||||||||||||||
| Current time is 06:35 am | Page: 1 2 |
| > Jensen Healey & Jensen GT Tech > Brakes > Brake upgrade? | Top |
