| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| fuel leak stromberg | Rate Topic |
| Author | Post |
|---|
| Posted: 05-13-2020 10:54 pm |
|
1st Post |
|
Joenpate56 Member
|
I have tried tightening by hand the plug seem to turn in both directions without tightening I assume its the o ring seal or just loose. How is the plug secured.
|
||||||||||||||
| |||||||||||||||
| Posted: 05-13-2020 11:17 pm |
|
2nd Post |
|
mtechwim Member
|
Do you mean the big plug in the center of the bowl? If so be very careful with it it has plastic parts, I could make a foto in the morning ( in in the middle of the night now in Holland) I am buzzy refurbishing 2 now. There is a o ring seal.
|
|||||||||||||
| ||||||||||||||
| Posted: 05-14-2020 01:31 am |
|
3rd Post |
|
Joenpate56 Member
|
yes that is the one. a foto would be great
|
||||||||||||||
| |||||||||||||||
| Posted: 05-14-2020 02:59 am |
|
4th Post |
|
redracer Member
|
If the plastic plug on the very bottom center of the bowl is leaking, DO NOT ATTEMPT TO START YOUR CAR. the rear carb sits right over the starter/solenoid, and it would be INSTANT FIRE. If you haven't rebuilt the carbs in a while or run the car in a while, just rebuild the carbs(takes me 5-6 hours).
|
|||||||||||||
| ||||||||||||||
| Posted: 05-14-2020 11:12 am |
|
5th Post |
|
mtechwim Member
|
Here is are some foto’s Attachment: FF06D90B-92F4-4B92-AAC7-4CCA1FF5800D.jpeg (Downloaded 51 times) Last edited on 05-14-2020 01:43 pm by mtechwim |
||||||||||||||
| |||||||||||||||
| Posted: 05-14-2020 01:45 pm |
|
6th Post |
|
mtechwim Member
|
Here is an other model from kopper, no idee what the difference is.this one fare less fragile. If possible I would like to use this one in stead of the plastic one. Attachment: 2D672E47-A17E-413D-90FB-A231FE3CD74C.jpeg (Downloaded 51 times) Last edited on 05-14-2020 01:46 pm by mtechwim |
|||||||||||||
| ||||||||||||||
| Posted: 05-14-2020 02:59 pm |
|
7th Post |
|
Joenpate56 Member
|
Thanks for all the information. Luckily I noticed the leak before I got the car started. It was the front carb. I have ordered the o rings. How difficult is it to pull the plug out. Should I jut order a new one?
|
||||||||||||||
| |||||||||||||||
| Posted: 05-14-2020 04:34 pm |
|
8th Post |
|
mtechwim Member
|
The top one, is easy but becarvul, clean outside, spray some tread lube around, wait a bit and with a small screwdriver pull it out. Not on one side but around so I comes strait out. If you miss some plastic parts you have to open the bottom.
|
|||||||||||||
| ||||||||||||||
| Posted: 05-14-2020 04:47 pm |
|
9th Post |
|
mtechwim Member
|
The big kopper one is ideal when you want to replace the jet.
|
||||||||||||||
| |||||||||||||||
| Posted: 05-15-2020 06:26 pm |
|
10th Post |
|
Tom Bradley Member
|
If the bottom o-ring is leaking, then other rubber parts may be going bad as well. I recommend taking off the top on one of the carbs and check the condition of the rubber diaphragm. If it looks to be going bad, you might want to get a couple rebuild kits.
|
|||||||||||||
| ||||||||||||||
| Posted: 05-15-2020 06:35 pm |
|
11th Post |
|
Joenpate56 Member
|
thanks for all the help. my orings should be here today or tomorrow. ill let you know how it goes. I have already removed the plug so it should be simple
|
||||||||||||||
| |||||||||||||||
| Posted: 05-15-2020 06:38 pm |
|
12th Post |
|
mtechwim Member
|
I found out dat also the rubber seals from the throttle axle were shot. So I would advice a full refurbishment of the carbs to.
|
|||||||||||||
| ||||||||||||||
| Current time is 08:15 am | |
| > Jensen Healey & Jensen GT Tech > Carburetors > fuel leak stromberg | Top |
