| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Air Filter for Stromberg carbs | Rate Topic |
| Author | Post |
|---|
| Posted: 07-03-2018 06:39 am |
|
1st Post |
|
JH73 Member
|
I cannot seem to locate the K&N part # for my Carbs....Everything that I find does not have enough holes in the mounting plates for the vents!
|
||||||||||||||
| |||||||||||||||
| Posted: 07-03-2018 01:40 pm |
|
2nd Post |
|
Brett Gibson JH5 20497 Member
|
http://www.cbperformance.com/product-p/3378.htm try this site, in my opinion they are a much nicer and robust filter assembly than a K&N. Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 07-03-2018 04:31 pm |
|
3rd Post |
|
redracer Member
|
The K&N have a knock-out hole(about 1/2' diameter) in the backing plate. you can make up a vent with some plastic or brass hardware for the breather tubes. The ones Brett described look like they're for other carbs, not the Strombergs?? Don't really know if CB Performance has anything for Strombergs??
|
||||||||||||||
| |||||||||||||||
| Posted: 07-03-2018 09:38 pm |
|
4th Post |
|
Brett Gibson JH5 20497 Member
|
Oops, Bruce is correct these air cleaners are for Dellorto’s. not Strom’s. Sorry about that. Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 07-04-2018 06:03 am |
|
5th Post |
|
Frank Schwartz Member
|
Brett: Do you know if this item actually fits a JH set of Strombergs..or if it will fit a JH setup with Webers..I just came across a JH with Webers and was considering putting them on Marks JH, but have no air filters and wondered if they will fit.. Regards Frank
|
||||||||||||||
| |||||||||||||||
| Posted: 07-04-2018 02:02 pm |
|
6th Post |
|
Brett Gibson JH5 20497 Member
|
Frank, yes these air filters are for both the Dell's and Weber's, you need to know the length of the velocity stacks on your carb's and then get the appropriate assembly. My Dell's are using the 3-14" so I am actually using these. http://www.cbperformance.com/product-p/3377.htm I cut the bolt bracket off the end cleaner, but kept it for the back one. so if need be I could put a return spring on the linkage. I really like them because the "Rib's" on them mimic the JH valve covers. Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 07-08-2018 07:21 am |
|
7th Post |
|
Frank Schwartz Member
|
Brett: You first showed a 3378 and then a 3377...I (being dense) am confused. Which is it?? Frank
|
||||||||||||||
| |||||||||||||||
| Posted: 07-08-2018 03:10 pm |
|
8th Post |
|
Brett Gibson JH5 20497 Member
|
Frank, It depends on what length velocity stack's you have on the carbs. If you visit the web site they list the 1-1/2" for shorter stacks, 2-1/2" for taller, 3-1/4" all the way up to a 6". this link now is the web page. and just the first page #1 of 5 pages. http://www.cbperformance.com/Air-Filters-Accessories-s/271.htm The air cleaner that I am using is the 3377. Brett
|
|||||||||||||
| ||||||||||||||
| Posted: 07-08-2018 05:50 pm |
|
9th Post |
|
Frank Schwartz Member
|
Hmmm.. these Webers have no stacks at all... Frank
|
||||||||||||||
| |||||||||||||||
| Posted: 01-20-2023 02:44 pm |
|
10th Post |
|
sbalian1 Member
|
Brett: Long ago there were air filter posts for carbs. Was there a supplier (not KN) for Stromberg carb filters?
|
|||||||||||||
| ||||||||||||||
| Posted: 01-20-2023 11:13 pm |
|
11th Post |
|
Brett Gibson JH5 20497 Member
|
If you Google stromberg air filter ram flow Moss Motors pops up with a alternative.
|
||||||||||||||
| |||||||||||||||
| Posted: 01-20-2023 11:29 pm |
|
12th Post |
|
sbalian1 Member
|
Thanks Brett.
|
|||||||||||||
| ||||||||||||||
| Current time is 07:37 am | |
| > Jensen Healey & Jensen GT Tech > Carburetors > Air Filter for Stromberg carbs | Top |
