Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Stromberg Gas Leak  Rating:  Rating
AuthorPost
 Posted: 05-16-2011 05:49 pm
  PM Quote Reply
1st Post
Jay
Member


Joined: 08-05-2005
Location: Canton, Ohio USA
Posts: 73
Status: 
Offline
I noticed gas dripping from what looke like a plug in the bottom of the front carburetor bowl. At first look it appeared that the plug is made of a type of plastic (I'm not sure). I have not yet attempted to take it out. Can anyone tell me what is the best approach to remove it. I believe that I have read that there is an o-ring in there. Do you think an o-ring replacement is all that is required? I don't seem to have any basic problems with the running characteristics of the engine so I am not wanting to venture into any carburator rebuild. Are the parts thet I would need available without the need to purchase an entire rebuild kit? How do I go about fixing this leak?

Thanks for any and all help that can be provided.

Jay

 

Back To Top PM Quote Reply  

 Posted: 05-16-2011 07:52 pm
  PM Quote Reply
2nd Post
subwoofer
Member
 

Joined: 04-01-2008
Location: Sandefjord, Norway
Posts: 617
Status: 
Offline
Whatever you do: DO NOT DRIVE THE CAR until the leak is fixed! We don't need another statistic! If fuel is allowed to reach the distributor - nicely placed just below the carbs - a fire is guaranteed.

The plug is just that, a plug - held in place by an O-ring. Just pull it straight down, replace the O-ring with a new one of good quality and push it back up. Job done. The O-ring should be available at any hardware or industrial supply store.

--
Joachim

Back To Top PM Quote Reply

 Posted: 05-16-2011 08:54 pm
  PM Quote Reply
3rd Post
Jay
Member


Joined: 08-05-2005
Location: Canton, Ohio USA
Posts: 73
Status: 
Offline
So there is no turning involved other than trying to loosen the fit of the o-ring? There are no threads?

Back To Top PM Quote Reply  

 Posted: 05-16-2011 10:33 pm
  PM Quote Reply
4th Post
Ron Mau
Member
 

Joined: 03-14-2005
Location: Davenport, Iowa USA
Posts: 61
Status: 
Offline
Correct . No threads it is just a push fit. It has 2 ears/ tabs on the plug that hold it in place. Pull down and it should pop out. Replace the o ring and you are good to go.

Ron Mau

Back To Top PM Quote Reply

 Posted: 05-17-2011 02:04 pm
  PM Quote Reply
5th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Dont use a Buna O-ring you need a gas compatable material, Nitrile is a good choice, you can probably buy just the o-ring from any number of on-line british parts places and while your at it get two and do the other carb it's probably the same age as the one leaking.

Brett

Back To Top PM Quote Reply  

 Posted: 05-20-2011 06:04 pm
  PM Quote Reply
6th Post
Jay
Member


Joined: 08-05-2005
Location: Canton, Ohio USA
Posts: 73
Status: 
Offline
I replaced both of the O-Rings with 5/8" ID x 13/16 OD standard O-Rings from a local NAPA store. The material was listed as Nitrile. I found the following information on a website and it would appear that this material would be okay for this application. Apparently Buna N would be okay (Petroleum Products). Any other thoughts on the Buna material? Should I find another replacement? Is the Nitrile (Buna N) is okay?

For those who may wonder what the plug looks like, I have included a photo of it.

The plugs pull right out. Maybe a little too easily but I guess that may be just an indicator that their sealing ability may have been depleated. The old O-Rings seened to be a bit soft.

Thanks for the help.

 

Nitrile (NBR or Buna N)

Due to it’s ability to be compounded for service over a temperature range of -65°F to +275°F, and it’s excellent resistance to petroleum products, Nitrile is the most widely used elastomer. Nitrile o-ring compounds can exhibit excellent compression set resistance, tear resistance, and abrasion resistance.

These compounds do not exhibit good resistance to ozone, sunlight or weather.

Attachment: PICT2197(1).JPG (Downloaded 69 times)

Back To Top PM Quote Reply

 Posted: 06-07-2012 06:02 pm
  PM Quote Reply
7th Post
sjensen24
Member
 

Joined: 08-05-2005
Location: Brooklyn Park, Minnesota USA
Posts: 78
Status: 
Offline
I just went through the same drill.  The plug in my carb has 4 tabs (stromberg manual indicates there should be 4).  I could not push in all 4 at once and push the plug out until I invented and fabricated a tool out of light gage sheet metal.  photo attached.

Attachment: JH brakes and carb tool 023.jpg (Downloaded 155 times)

Back To Top PM Quote Reply  

 Posted: 02-25-2013 01:02 am
  PM Quote Reply
8th Post
igdboss
Member


Joined: 08-31-2012
Location:  
Posts: 21
Status: 
Offline
Mine was gushing fuel. In the process of removing the plug the tabs broke off. Any suggestions for where to procure a replacement?

Back To Top PM Quote Reply

 Posted: 05-19-2013 08:06 am
  PM Quote Reply
9th Post
Frank Schwartz
Member
 

Joined: 02-18-2011
Location:  
Posts: 313
Status: 
Offline
Yes...try Delta Motorsports for the O ring and also for a replacement plug...that should do it...

Back To Top PM Quote Reply  

Current time is 08:06 pm  
> Jensen Healey & Jensen GT Tech > Carburetors > Stromberg Gas Leak Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems