Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Carburetors > Carburetor adjustment

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Carburetor adjustment  Rating:  Rating
AuthorPost
 Posted: 09-01-2009 03:49 pm
  PM Quote Reply
1st Post
sjensen24
Member
 

Joined: 08-05-2005
Location: Brooklyn Park, Minnesota USA
Posts: 78
Status: 
Offline
My Strombergs seem to be running too lean (per the air valve lift test).  I have maxed out the enriching adjustment and they still seem to be too lean.  I just read in the stromberg book that screwing the idle trimming screw in enriches the mixture.  It is apparently screwed out on new engines and needs to be screwed in as the engine loosens.  Does anyone have experience with this?

Back To Top PM Quote Reply  

 Posted: 09-02-2009 01:02 pm
  PM Quote Reply
2nd Post
Mitch Ware
Member


Joined: 03-12-2005
Location: Albany, New York USA
Posts: 204
Status: 
Offline
Have they ever been rebuilt? As the bronze shafts and guides wear they will start allowing air to enter through those gaps, causing a too lean issue. The only way to cure it is to rebuild or replace them

Mitch Ware
#19670

Back To Top PM Quote Reply

 Posted: 09-02-2009 01:52 pm
  PM Quote Reply
3rd Post
sjensen24
Member
 

Joined: 08-05-2005
Location: Brooklyn Park, Minnesota USA
Posts: 78
Status: 
Offline
I just got the rebuild kits in the mail from Delta.  I did find a vacuum leak.  Fixiing that helped but it still feels like something is holding back.  By the way, the Stromberg book says there is an idle trimming screw, but I do not see such a thing on my carbs.

Back To Top PM Quote Reply  

 Posted: 09-05-2009 05:39 am
  PM Quote Reply
4th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Have been watching this thread as my problem is the opposite from sjensen24's. 17798 is a gas hog. Wasn't so bad when I first brought it from San Diego, but since I kitted the carbs it's thirst has been unquencheable. I have fiddled them back to almost where they were before I tried to improve them, but they are still way rich. I hesitate to adjust the needles any leaner for fear of unscrewing them from the adjusters. Which is the way they were when I disassembled them for cleaning and kitting. Am going to try another quarter turn CCW, but a dasn't go any further. Any thoughts or comments welcomed.

Back To Top PM Quote Reply

 Posted: 09-05-2009 02:40 pm
  PM Quote Reply
5th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Float bowl level and condition of shutoff valve,plus check to make sure the choke lever is not contacting, all add to richness, and while your at it block of the bypass valve and temp compensator, thier more trouble than they are worth and you will have no ill effects if you do.

And one additional, spray some oil onto the the butterfly shaft seals while the engine is running, if the engine improves then you have a leak there as well, they are not a normal item in a rebuild kit but you can still purchase them.

Brett 

Back To Top PM Quote Reply  

 Posted: 09-05-2009 04:32 pm
  PM Quote Reply
6th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Thanks for the reply, Brett! The kits I got had new inlet needles and seats, and also the shaft seals, but I may have goofed the install, somehow. AIUI the temp compensators open up and add air when hot. I have fooled with them and they are opening now as I think they are supposed to. Maybe that will help lean the carbs out. I hate to block the bypass after installing all those neat new pieces, but I like making things simpler. When you say "block off" are you refering to the vacuum line to them?I may just have to back up and redo the carb work, now that I have a little better idea of what I'm doing.

Back To Top PM Quote Reply

 Posted: 09-07-2009 01:43 pm
  PM Quote Reply
7th Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Yes, remove the vac line and also the diaphram, replace that with a full gasket so it blocks off any holes in the carb body.

Brett 

Back To Top PM Quote Reply  

 Posted: 09-07-2009 03:23 pm
  PM Quote Reply
8th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Thanks Again,
  I think you may have nailed a problem for me. I had blocked the vacuum line that goes to the bypass gadgets at the intake manifold, but had not removed the diaphragms or blocked any holes in the carbs. I will tend to this and let you know the result.

Back To Top PM Quote Reply

 Posted: 09-13-2009 03:38 am
  PM Quote Reply
9th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Well, I cut some dandy blanking gaskets and installed them next to the carb bodies, but I didn't have the heart to remove the diaphragms that I had just installed. I figure with the gaskets and the vacuum hoses blocked that should do what is needed. After a nice drive today, some 50 miles all totaled, I think I may have made an improvement. Idle is not quite as fussy and mileage seems to be better, though I haven't confirmed that yet. In reviewing my notes, it would seem the mileage dropped off after I changed the cam timing to the 110-110 setting. Can't say for sure, so probably shouldn't say at all. I do know my mileage records from our trip in July of 08 were showing 2-4 mpg better than any recent figures I have. Thanks all, for the good words and encouragement.

Back To Top PM Quote Reply  

Current time is 08:18 pm  
> Jensen Healey & Jensen GT Tech > Carburetors > Carburetor adjustment Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems