| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Strombergs rising ide | Rate Topic |
| Author | Post |
|---|
| Posted: 06-08-2008 02:06 am |
|
1st Post |
|
rossjfox Member
|
Hello all! I recently purchased JH 20340! Overall, a lot of restoration has been done, and considering I drove it home 550 miles without difficulty, i have no complaints! My question involves the idle. It has strombergs, and with timing set at 8-10 BTDC, i can comfortably adjust the idle to btw 800 - 1000. But then, once out on the road, the idle will slowly climb to 1200 - 1300. Mostly annoying & with the cost of fuel, not appreciated! Any ideas? I was thinking a vacuum issue, possibly with higher operating temps once out on the road? Any help trouble shooting would be a help. Thanks in advance. Ross
|
||||||||||||||
| |||||||||||||||
| Posted: 06-08-2008 04:02 pm |
|
2nd Post |
|
edward_davis Member 
|
Ross, The CD carbs have a bi-metallic spring inside them to adjust the richness with temperature. Many people have disabled this bit, but if the spring gets out of adjustment, it can cause problems. Also, I have noticed that just letting my JH warm up by idling doesn't get the carbs hot enough to activate the spring. Adjusting the idle (or the richness) then won't get you to the right place when the car is running on the highway. My solution was to just re-adjust the idle on the road after I got the car going. That seems to have worked pretty well. The other solution is to pick routes with as little idling as possible.... =) Welcome to the club! (Where are you located?) Edward Davis
|
|||||||||||||
| ||||||||||||||
| Posted: 06-08-2008 10:34 pm |
|
3rd Post |
|
dwalls1 Member
|
Really appreciate this post and the response, as I'm having some problems adjusting the idle on 17798. Will try again after a good warm up. While I'm at it, can anyone help me out with how much oil to put in the Strombergs dash pots? The book says to "fill" them. Does this mean pour it in 'til it runs out? Thanks again. Dale
|
||||||||||||||
| |||||||||||||||
| Posted: 06-08-2008 11:16 pm |
|
4th Post |
|
Jensen Healey Super Moderator 
|
The dashpots help to richen the mixture during acceleration. Fill with 20-50 to about 1/2" from the top. It's not critical if they overflow, just mop up.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-09-2008 02:32 am |
|
5th Post |
|
rossjfox Member
|
Ed, Thanks for the advice! I'll try to adjust with the engine full hot. Regarding the bi-metallic spring, how would you disable this? I know it's the long device on the side of the carbs; I can't imagine that you can just remove it. BTW, I'm located in Denville, NJ. Not far from Morristown. Ross Last edited on 06-09-2008 02:34 am by rossjfox |
||||||||||||||
| |||||||||||||||
| Posted: 06-09-2008 02:55 am |
|
6th Post |
|
Jensen Healey Super Moderator
|
Remove the cover and flip the flat metal spring over.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-10-2008 03:48 pm |
|
7th Post |
|
rossjfox Member
|
Thanks! I'll keep you updated. Ross
|
||||||||||||||
| |||||||||||||||
| Current time is 10:01 pm | |
| > Jensen Healey & Jensen GT Tech > Carburetors > Strombergs rising ide | Top |
