| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Clutch Cable Installation--Help! | Rate Topic |
| Author | Post |
|---|
| Posted: 10-27-2007 09:08 pm |
|
1st Post |
|
j4jacob Member
|
For some reason, the shop manual I have doesn't cover clutch cable installation very well. Since the old one had snapped I had no trouble removing it but the installation of the new one at the pedal end has me scratching my head. Iv'e tried to get my hand up into the pedal box from the floor board but it is VERY tight up there. Can the cable retainer be removed/reinstalled with a very long needle nose plier? If this approach is not viable I see no other way than to pull the entire pedal box forwad into the engine bay. I'm reluctant to unbolt the pedal box because I don't want to break the seal and I don't want to disconnect the brake lines to the master cylinder unless of course I must. Any advice on the best/easiest way to get at this is most appreciated! Albert
|
||||||||||||||
| |||||||||||||||
| Posted: 10-28-2007 04:02 pm |
|
2nd Post |
|
Steve Jarvis Member
|
I went through the same process for several hours one night to figure out how to replace the clutch cable. The only solution I came to was to remove the bolts from the housing and pull it out several inches. You also need to unbolt the the brake balancing unit from the wheel wheel. This saves removing the brake lines from the master cylinder and bleeding the lines. You will find that when the housing comes out the pin for the cable is held in place by a clip that needs to be compressed in order to remove the pin. It is not physically possible to do this without removing the housing. On the new clutch cable I had, the ball that slips through the connector was too large. I ground it down with a dremel tool until it slipped through. Have fun. Steve
|
|||||||||||||
| ||||||||||||||
| Posted: 10-31-2007 02:23 am |
|
3rd Post |
|
j4jacob Member
|
Thanks Steve! Once you put me on the right course, it wasn't a bad job, just a bit fiddly and time consuming. Most appreciated....Albert
|
||||||||||||||
| |||||||||||||||
| Posted: 06-06-2008 02:05 am |
|
4th Post |
|
D.Drake Member
|
Steve just saw your response to Albert .I had thought I would have to remove the pedal box in order not to kink the brake lines and still get enough room to work on the clevis pin . Thanx David
|
|||||||||||||
| ||||||||||||||
| Posted: 06-20-2020 09:08 pm |
|
5th Post |
|
Sean Burke Member
|
Does anyone have a picture of where the clutch cable routes/attached at the front of the oil pan just under the crank pulley? Any picture/help would be appreciated
|
||||||||||||||
| |||||||||||||||
| Posted: 06-20-2020 10:48 pm |
|
6th Post |
|
discogodfather Member 
|
My cable is attached via a bolt clip to the block just above the pan. It has some rubber tube to help with heat.     
|
|||||||||||||
| ||||||||||||||
| Posted: 06-21-2020 02:57 pm |
|
7th Post |
|
Jim Ketcham Member
|
On the 74 JH the clutch cable attaches to the PDWA on top and the front of the timing belt cover spacer stud below. The rubber tubes are for abrasion protection on the oil pan. Attachment: C9AA992F-A22B-4308-A60E-51300950BB29.jpeg (Downloaded 55 times) Last edited on 06-21-2020 08:26 pm by Jim Ketcham |
||||||||||||||
| |||||||||||||||
| Posted: 06-21-2020 03:11 pm |
|
8th Post |
|
Jim Ketcham Member
|
Sorry, I can't seem to attach photo no matter how small I make it.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-21-2020 03:21 pm |
|
9th Post |
|
Jim Ketcham Member
|
I seem to be having a bad day at communicating. I meant to say timing belt cover NOT “fan shroud”. Sorry about that.
|
||||||||||||||
| |||||||||||||||
| Posted: 06-21-2020 03:43 pm |
|
10th Post |
|
Sean Burke Member
|
Thank you for the pics. One more item I can put on and cross off the list after my motor rebuild!
|
|||||||||||||
| ||||||||||||||
| Current time is 11:44 pm | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > Clutch Cable Installation--Help! | Top |
