| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Lotus Excel cams / housings | Rating: 
|
| Author | Post |
|---|
| Posted: 06-02-2006 09:33 pm |
|
1st Post |
|
Tim Orme Member
|
Hi, wondering if anyone can advise. New to the message board so if the topic's been covered before, forgive me ! I have a set of Lotus Excel SE cams / housings (107/104 combination), I'm intending to fit them to my standard U.K. spec 907 engine and move to an HTD belt / vernier pulley set. Will these cams be worth using in my engine or should I put my standard cams into the Excel housings. What cam timing figures should I use. Any advice appreciated Tim
|
||||||||||||||
| |||||||||||||||
| Posted: 06-03-2006 12:07 am |
|
2nd Post |
|
Greg Fletcher Administrator 
|
The 107/104 combo with vernier pulleys is a very cool setup. There are a number of great posts on the board, try the search feature and see what comes up. You'll be looking for a 104 MOP to really take advantage of what the cams can offer and needless to say a 2.2 would provide the best basis for that. Some among us would say you simply must have the 2.2, but I think the standard 2 liter can still offer enough to make your switch well worth the effort.
|
|||||||||||||
| ||||||||||||||
| Posted: 06-03-2006 08:57 am |
|
3rd Post |
|
Tim Orme Member
|
Thanks for the advice Greg, funds won't stretch to a 2.2 conversion at the moment but it's something that I will be considering in the future.
|
||||||||||||||
| |||||||||||||||
| Posted: 06-03-2006 03:39 pm |
|
4th Post |
|
Jensen Healey Super Moderator 
|
The 104 cam will cause binding of the stock valve springs. You will need to either change the springs to the performance version or use a milder cam. I have been taking baby steps with performance upgrades. I have a pair of 107 cams but I know that installing them and getting them shimmed could have the car down for weeks. Most of the time is spent waiting for shims. I also have not purchased any 104 pulleys but have a set of 102's from a later JH. Then there's the re-tuning of the Dellortos.... Call me lazy, Kurt JH 13148
|
|||||||||||||
| ||||||||||||||
| Posted: 06-03-2006 05:59 pm |
|
5th Post |
|
Tim Orme Member
|
Thanks Kurt, that's something I hadn't considered ! So it's head off as well then (just changed the head gasket - typical) Wanted to use the later cam housing to eliminate the oil leaks once and for all - can't seem to make the re-useable gaskets seal properly and each time you want to check the valve clearances, it's oil over the manifold (sorry - headers) time !
|
||||||||||||||
| |||||||||||||||
| Posted: 06-04-2006 02:08 am |
|
6th Post |
|
Jensen Healey Super Moderator
|
It would be cheaper to use two 107 cams and skip the cost of new springs, head gasket, exhaust gaskets, and intake gasket. Just a note on valve adjustment, shoot for the high side on the clearance. The clearances only get tighter and it should stay within tolerance longer. Kurt
|
|||||||||||||
| ||||||||||||||
| Posted: 06-04-2006 02:28 pm |
|
7th Post |
|
LambandAndy Member 
|
I have removed valve springs on other engines by making an adapter to screw into a spark plug hole and applying compressed air to keep the valve in place while using an "overhead" style valve spring compressor to remove the collets. Never tried it on a Lotus motor but it should work. Andy
|
||||||||||||||
| |||||||||||||||
| Current time is 07:13 pm | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > Lotus Excel cams / housings | Top |
