Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Engine & Transmission > Oil pan gasket or seal replacement

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Oil pan gasket or seal replacement  Rate Topic 
AuthorPost
 Posted: 11-05-2021 11:25 pm
  PM Quote Reply
1st Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Has anyone tried to reseal the oil pan by unbolting and dropping pan straight down and resting in the front crossmenber. I looks like there is 1 to 2 inch clearance where you could strip off the old gasket and use rtv then bolt it back up? I just changed my clutch and the car is up about 20 inches. It looks possible.

Back To Top PM Quote Reply  

 Posted: 11-07-2021 06:34 am
  PM Quote Reply
2nd Post
Esprit2
Member
 

Joined: 05-01-2005
Location: Minneapolis, Minnesota USA
Posts: 575
Status: 
Offline
I'll pass on the question about "Is there enough room". But I will strongly recommend that you not use an RTV silicone sealant.

When you bolt the joint back together, it's likely that some excess silicone will squeeze out of the joint. No big deal on the outside, you just wipe off the excess with a rag, and no mess.

However, for every bit of silicone that oozes 'out', you can just about bet a similar amound oozes to the inside of the engine. The ooze cures to a string of little rubber beads clinging to the joint line by a very thin film of silicone. Over time, engine vibration causes the beads to break off, then they migrate (ride the oil flow) to the sump.

I hate to think of the number of engines I have opened after they ran the bearings due to oil presssure failure. Only to find the oil pick-up screen plugged by a mess of little silicone rubber beads. The plugged screen is why the oil pressure crashed in an otherwise healthy engine.

Your choice, but I will not use RTV silicone sealant in an engine... with only a very few exceptions. The sump isn't one of those exceptions.

Regards,
Tim Engel

Back To Top PM Quote Reply

 Posted: 11-07-2021 03:47 pm
  PM Quote Reply
3rd Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
Agree strongly with Tim's recommendations along with the possible calamity of oil pick-up tube blockage. Personally, I would use silicone ONLY on the water pump or thermostat gasket, but still prefer Permatex #2 even there.

Back To Top PM Quote Reply  

 Posted: 11-08-2021 12:07 am
  PM Quote Reply
4th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Ok. Rtv is not a good choice , however , it doesn't answer my question can you drop the oil pan enough to gain access to the seal flange . If so, is there enough clearances to slide in a new gasket or use a different sealer that is not silicone based.

Back To Top PM Quote Reply

 Posted: 11-08-2021 01:04 am
  PM Quote Reply
5th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
Having worked on "many", I have looked at that long ago and decided it was not worth the effort. If I remember correctly, you would have to raise the engine slightly just to clear the front subframe.
But hey, give it a shot and let us know what you have determined.
As you know or have read in the "shop" manuals, to change the clutch they want you to pull the engine, which as most know, is not necessary, so maybe you have a "new" way!

Back To Top PM Quote Reply  

 Posted: 11-08-2021 10:26 pm
  PM Quote Reply
6th Post
Tom Bradley
Member
 

Joined: 07-15-2013
Location:  
Posts: 205
Status: 
Offline
Not a chance unless you can come up with some way to jack up the engine. I jacked up my car and took a quick look. The smallest gap between the bottom of the pan and the frame is less than 3/8". The length of the studs and bolts holding pan on are about 1". The only way I have ever been able to safely jack up the engine is by putting piece of wood under the oil pan to spread out the force, so that pretty much cancels out that possibility unless you use a hoist to lift it from the top. I also don't see any way to get a wrench on some of the bolts. Sorry.

Last edited on 11-08-2021 10:26 pm by Tom Bradley

Back To Top PM Quote Reply

 Posted: 11-16-2021 01:16 am
  PM Quote Reply
7th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Thanks for all your advise, looks like an engine pull next.

Back To Top PM Quote Reply  

 Posted: 11-16-2021 06:36 pm
  PM Quote Reply
8th Post
noomg
Member
 

Joined: 08-02-2018
Location: Long Beach, California USA
Posts: 458
Status: 
Offline
Jomac,

You could also drop the front suspension and steering, it basically comes out as a unit, Ant did it on Wheeler Dealers. You'll have to support the motor from above but it should give you good access to the oil pan.

Also if the front suspension needs to be rebuilt you can do it comfortably on a work bench rather than working under the car.

Back To Top PM Quote Reply

 Posted: 09-25-2022 02:41 pm
  PM Quote Reply
9th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
sorry for the long delay , harborfreight.com sells a engine bar to support the engine from above using the fender flanging as support for 90$. Then I can drop the front crossmember. replacing the suspension bushings and dropping oil pan.
Looks like the best and easiest way to do the leaking oil seal.

Back To Top PM Quote Reply  

 Posted: 09-25-2022 04:33 pm
  PM Quote Reply
10th Post
redracer
Member
 

Joined: 09-10-2012
Location: BROOKHAVEN, Georgia USA
Posts: 654
Status: 
Offline
jomac: years ago I made a support for the engine block for exactly the same purpose, rebuilding the front suspension. I used wood(2'X4"s would work, but a piece of oak from a home center is stronger) since the entire engine with the ancillaries only weighs 275 lbs.
I added extra "blocks" onto the ends so it would sit on the 1 1/2" wide support beams and used strapping under the engine.
If you plan to rebuild the entire front, I STRONGLY recommend welding an extra 1/8" plate to the front lower frame where the lower arm bolts come through. The rear part has a second piece of metal from the subframe, but the front hole gets wallowed out from normal forces on that one "thin" piece.

Back To Top PM Quote Reply

 Posted: 09-26-2022 12:20 am
  PM Quote Reply
11th Post
jomac
Member
 

Joined: 09-16-2016
Location:  
Posts: 71
Status: 
Offline
Thanks for all the responses, this will be my winter project.
Last winter I did a new clutch, one piece driveshaft, Holley sniper efi And pertronix ignitor 2 , .
Wow want a difference!!

Back To Top PM Quote Reply  

Current time is 06:55 pm  
> Jensen Healey & Jensen GT Tech > Engine & Transmission > Oil pan gasket or seal replacement Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems