| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| removing cylinder head | Rating: 
|
| Author | Post |
|---|
| Posted: 05-09-2013 11:05 pm |
|
1st Post |
|
StevenD57 Member 
|
If I am trying to remove the cylinder head from a 1974 Jensen-Healey, do I need to remove the brake booster or anything else so the head will slide off the head studs with the engine still in the car?
|
||||||||||||||
| |||||||||||||||
| Posted: 05-10-2013 06:00 pm |
|
2nd Post |
|
Jim Ketcham Member
|
I can't imagine pulling the head with the engine in the car. I believe you'll find it easier in the long run to pull the engine. It makes proper reassembly much easier, especially shimming the valves.
|
|||||||||||||
| ||||||||||||||
| Posted: 05-11-2013 01:00 pm |
|
3rd Post |
|
Arvin Appelman Member
|
The head can be removed without removing any peripherals. Be very careful when removing the cam towers so you son't loose any shims. Push the buckets down as you lift the tower to keep the shims trapped on the valve.
|
||||||||||||||
| |||||||||||||||
| Posted: 11-04-2013 08:52 pm |
|
4th Post |
|
wtberks Member
|
I pulled the head and replaced it on my GT without touching the brake booster. It is a little close around the rear most bolts, but nothing really difficult.
|
|||||||||||||
| ||||||||||||||
| Posted: 10-06-2015 07:45 pm |
|
5th Post |
|
Jay Member 
|
I'm looking at the need to get into the valves. I'm suspecting a burnt valve. Question, do I need to remove the cam towers from the head before I can remove the head from the block? Or, can I just remove the valve covers to access the head bolts and remove the head, cam towers and camshafts as a complete assembly. I may getting a little ahead of myself, as I need to get a compression check first, but so far I appear to have a dead cylinder. I have spark on the plug. The engine will run on 3 cylinders. Cylinder #2 appears dead.
|
||||||||||||||
| |||||||||||||||
| Posted: 10-06-2015 07:54 pm |
|
6th Post |
|
wtberks Member
|
You must remove the cam towers as them block the head bolts. If you do not have the workshop manual for this engine, you really need to get one. It is not rocket science, but it is a bit different from the other engines I have touched. You will find out things such as not mixing up the shims for the cam. The right way to replace the head and cam towers. Where the timing marks on the cam gears line up. By the way, I used West Coast Cylinder Heads to rebuild my engine's head, as per a lot of recommendations. They were very good, knew the ins and outs of the 907 head, but were a bit slow. My advantage was that I could drive to their shop during my lunch time. Last edited on 10-06-2015 07:56 pm by wtberks |
|||||||||||||
| ||||||||||||||
| Posted: 10-06-2015 08:02 pm |
|
7th Post |
|
Jay Member
|
Would anyone have a suggestion on where I could find a workshop manual for the 1974 Lotus 907 engine? I would love to read all about such a project.
|
||||||||||||||
| |||||||||||||||
| Posted: 10-06-2015 08:14 pm |
|
8th Post |
|
wtberks Member
|
You can start here: http://www.deltamotorsports.com/products/pg18a-books-and-manuals.html. There are a number of people on the list who are very knowledgable about this engine. Especially in regards to procedures that were developed after Jensen stopped producing these cars.
|
|||||||||||||
| ||||||||||||||
| Posted: 10-08-2015 05:43 am |
|
9th Post |
|
rovohn Member 
|
I found a manual on CD on Ebay,then you can print the pages you need Cheers,John
|
||||||||||||||
| |||||||||||||||
| Posted: 11-17-2015 11:04 pm |
|
10th Post |
|
Esprit2 Member
|
Jay wrote:Would anyone have a suggestion on where I could find a workshop manual for the 1974 Lotus 907 engine? I would love to read all about such a project.Jay, Go to my Dropbox folder, here: https://www.dropbox.com/sh/4kxqw9vlsnz54lf/AACCyvB-TfYKLI1qM-e_IUlTa?dl=0 There are some manual PDFs in there, as well as the very helpful Technical Data Section, A (TDA). Also notice the sub-folder titled Jensen-Healey Parts & Tech and browse there as well. In there, notice the files titled "Cylinder Head Gasket - Goetze Composite Installation Instructions.doc", and "Engine Rebuild Data, 4-cyl.xls", and "Cooling - Water Pump - Rebuild - Instructions, 6 pgs.doc". Everything is downloadable. Regards, Tim Engel Last edited on 11-17-2015 11:21 pm by Esprit2 |
|||||||||||||
| ||||||||||||||
| Posted: 11-18-2015 05:43 am |
|
11th Post |
|
Frank Schwartz Member
|
Cylinder 2 not firing? Check for a spark.......
|
||||||||||||||
| |||||||||||||||
| Current time is 09:18 pm | |
| > Jensen Healey & Jensen GT Tech > Engine & Transmission > removing cylinder head | Top |
