Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Timing belt tension  Rate Topic 
AuthorPost
 Posted: 05-11-2008 10:50 pm
  PM Quote Reply
1st Post
D.Drake
Member
 

Joined: 01-15-2006
Location: Keswick, Ontario Canada
Posts: 14
Status: 
Offline
I have my 73 MkI  back on the road (almost) !
I have changed the timing belt sevearl times over the years ,but with out a guage it is by guess and by golly .
Someone on the list recommended that you  could estimate  the tension by twisting the belt 45 degrees  between the alternator pulley and intake cam .
I tried this and the belt is whining (too tight)
Anyone have a technique that they feel gives them a good result without using a Burroughs Gauge .

Back To Top PM Quote Reply  

 Posted: 05-11-2008 11:10 pm
  PM Quote Reply
2nd Post
D.Drake
Member
 

Joined: 01-15-2006
Location: Keswick, Ontario Canada
Posts: 14
Status: 
Offline
I just rediscovered the old Message archive ,and found that the locationI chose to twist  ,between the dizzy pulley and Intake was not right .Should have been between the exhaust pulley and Crank
Also a recommendation of 3/8 " deflection between the dizzy pulley and Intake was recommended .
I just hate having to keep readjustingthe timing belt  because I have to remove the alternator to access the rear tensioner nut .I really should have changed to the newer style tensioner ;-(

Back To Top PM Quote Reply

 Posted: 07-06-2008 12:39 am
  PM Quote Reply
3rd Post
Steve Jarvis
Member
 

Joined: 10-28-2006
Location: Mississauga, Ontario Canada
Posts: 51
Status: 
Offline
Since I don't have the device to measure the belt tension (or know where to get one) I wanted to understand the process. Do you mean that the belt should be able to be pushed in 3/8" from the resting position? How much pressure are you using?

Thanks

Back To Top PM Quote Reply  

 Posted: 07-06-2008 04:26 pm
  PM Quote Reply
4th Post
John Finch
Member
 

Joined: 08-01-2005
Location: Minneapolis MN
Posts: 122
Status: 
Offline
Try finding a Burroughs or Robinair guage on ebay or google. Model numbers that are known to work for the Lotus 907 are (Burroughs) BT-33-86J, BT-33-73F and Robinair 10240. I found the Robinair on Ebay for about $25.00. Takes all the guess work out for cheap. Best of Luck.

Last edited on 07-06-2008 04:27 pm by John Finch

Back To Top PM Quote Reply

 Posted: 07-06-2008 04:55 pm
  PM Quote Reply
5th Post
Greg Fletcher
Administrator


Joined: 03-11-2005
Location: Lake Nacimiento, California USA
Posts: 430
Status: 
Offline
I lived for years without a belt tensioner gauge, so don't feel did like you must have one. As John mentions, it does take the guess work out of it.

One way to check the belt tension: place a metal straight edge on the belt from the distributor pulley to the intake cam pulley. Get an ink pen and mark your thumb nail with a mark 1/4 inch and 3/8 inch from the end of your nail. While holding the straight edge with one hand, push the belt down with your thumb as far as it will go in the center. The belt should deflect between 5/16 and 3/8 when adjusted to 95 pounds.

Back To Top PM Quote Reply  

 Posted: 07-18-2008 04:29 am
  PM Quote Reply
6th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Thanks Greg! Used this trick this week when I replaced my belt and idler bearings. First checked the old belt and found it within spec, then used it on the new one and got it dialed right in. Or should I say "nailed it".

Back To Top PM Quote Reply

 Posted: 07-19-2008 08:19 pm
  PM Quote Reply
7th Post
Steve Jarvis
Member
 

Joined: 10-28-2006
Location: Mississauga, Ontario Canada
Posts: 51
Status: 
Offline
I just tightened the belt up from about +1/2" of play to 5/16". Seems to be fairly easy. I did do it differently than the manual and did not remove the fan. Seems you can loosen the alternator and get in from that direction also.

Back To Top PM Quote Reply  

 Posted: 07-19-2008 09:56 pm
  PM Quote Reply
8th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
My fan is extended towards the radiator due to it's having had A/C installed, so that clearance is not an issue. I am in the process of moving the fan back against the pulley to make room for a fan shroud. Problem is cutting the extra sheave and length off the crank pulley as the original pulleys are NLA. Anyone out there have a stock pulley I could releave them of?

Back To Top PM Quote Reply

Current time is 05:30 pm  
> Jensen Healey & Jensen GT Tech > Engine & Transmission > Timing belt tension Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems