Home 
Home Search search Menu menu Not logged in - Login | Register
> Jensen Healey & Jensen GT Tech > Fuel Stuff > Tanks, you're welcome

 Moderated by: Greg Fletcher Page:    1  2  Next Page Last Page  
New Topic Reply Printer Friendly
Tanks, you're welcome  Rate Topic 
AuthorPost
 Posted: 01-22-2008 11:44 pm
  PM Quote Reply
1st Post
mdutch
Member


Joined: 03-12-2005
Location: Dallas, Texas USA
Posts: 74
Status: 
Offline
Well crap.  I just got my JH newsletter today, and have read with trepidation about the Aluminum tanks.  Of course, last summer I considered carefully and looked at options, then laid down the hard bucks to Jorge.  Caveat Emptor.  It looked reasonably like a tank, and the welds were generous.  I will NOT fight the good fight over who is right and what is good workmanship, but will try to salvage what's here. 

Given the experiences outlined in the JH article, I'm open for a roundtable of suggestions on how to proceed with this new aluminum tank that's virgo-in-tank-ta.  ;)

Possiblities I've considered (please suggest your own):
1.  Thorougly measure this sucker against the exisiting rusty steel tank, esp. as pertains to dimensions around the neck.
2.  Pressure test the tank, and/or skip to 3.
3.  Pre-emptively seal the inside of the tank with  ___________?  (insert name of favorite tank sealer goo here).

If anyone else has purchased an aluminum tank from aforementioned supplier and has comments, I'd appreciate them sharing their experience, either here or via PM.  You can e-mail me personally through jensen at audiowizardry dot com.

Last edited on 01-24-2008 03:08 am by mdutch

Back To Top PM Quote Reply  

 Posted: 01-25-2008 03:58 pm
  PM Quote Reply
2nd Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Man I'm sorry to hear people having trouble with these new tanks, you would think for that kind of money the bugs would be worked out, at the same time I also think that it was nice to see a company step up and help out the JH world to fill a void, goes back to the old saying " no good deed goes unpunished ".

Personally I think I would do what Erik Hawkes did and just make it work with a few mod's, as for sealing with a bit of RTV, heck if I didnt use that stuff there would be more fluids on my garage floor than in the car, I dont understand why that would be a issue.

my 2 cents. / Brett.

Back To Top PM Quote Reply

 Posted: 01-25-2008 03:58 pm
  PM Quote Reply
3rd Post
Brett Gibson JH5 20497
Member
 

Joined: 03-17-2005
Location: Hilton, New York USA
Posts: 798
Status: 
Offline
Man I'm sorry to hear people having trouble with these new tanks, you would think for that kind of money the bugs would be worked out, at the same time I also think that it was nice to see a company step up and help out the JH world to fill a void, goes back to the old saying " no good deed goes unpunished ".

Personally I think I would do what Erik Hawkes did and just make it work with a few mod's, as for sealing with a bit of RTV, heck if I didnt use that stuff there would be more fluids on my garage floor than in the car, I dont understand why that would be a issue.

my 2 cents. / Brett.

Back To Top PM Quote Reply  

 Posted: 01-27-2008 01:36 am
  PM Quote Reply
4th Post
Gary Martin JH 15371
Member
 

Joined: 03-12-2005
Location: Portland, OR
Posts: 98
Status: 
Offline
I also bought the Aluminum tank back the fall of 2005 as part of the original order of  tanks. However I am still working to paint my car and have not installed it yet. The tank is pretty much an exact copy of the original, the only difference I see is some of the vent tubing inside the top of the tank is a little different, but not an issue. The welds on my tank look fine. As noted the main issue with the tank is the seal on the side for the sending unit. Do not use the plastic ring that came with the tank. It is the right thickness, but is too hard to seal properly. The original rubber seal is too thin, either try to use a second seal like Erik Harkes has done, or perhaps construct a thin Aluminum ring to take up the extra space. Place the ring or second seal outside between the sending unit and locking ring. Tighten carefully so you do not bend the three tabs, or deform the sealing surface inside. Its too bad they did not use some thicker Aluminum for the sending unit flange area. I would not be opposed to using a small amount of some gas resistant sealant on the rubber seal if it did leak. Try first without. Once you have the sending unit sealed, it may not be a bad idea to have the tank pressure checked before installing to make sure all is well. I would stay away from coating the inside of the tank unless the welds leaked. I also would not paint the outside, Aluminum oxidizes and naturally prevents corrosion. See the 6 pages of comments in this forum under New Aluminum Tanks.

When installing the tank, use rubber strips underneath and behind the tank. Be sure to place some rubber between the steel tank straps and the Aluminum tank, or construct some Aluminum straps. If you don't, you can get what is called Galvanic corrosion, that is corrosion between to dissimilar types of metal. 

Gary

Back To Top PM Quote Reply

 Posted: 01-28-2008 11:28 am
  PM Quote Reply
5th Post
Harkes
Member


Joined: 03-17-2005
Location: Warmond, Netherlands
Posts: 216
Status: 
Offline
I could try and make a picture of the seal if interested? Indeed the aluminium is a little soft, so one has to be careful when tightening the locking ring.

I have tried the white locking ring provided with the tank and it leaks! so do not use! I followed up Gary's advice and went for a 2nd rubber seal. I haven't used any sealant, installed the tank, filled her up to the top and it stays dry.

I have been driving the car with the new tank and no issues at all.

The alu tank is indeed an exact copy of the original except for the vent tubes, but that is not a problem at all. On my tank all the welds look good.

Only issue is the white locking ring and therefore making it seal well.

Good luck

erik

Back To Top PM Quote Reply  

 Posted: 01-28-2008 06:17 pm
  PM Quote Reply
6th Post
mdutch
Member


Joined: 03-12-2005
Location: Dallas, Texas USA
Posts: 74
Status: 
Offline
I appreciate the heads-up on the locking ring.  As a "handyman" as well as bad mechanic, I raised an eyebrow at the enclosed white nylon ring for the seal.  Looked like a gasket for a sink drain.  So I will definitely pay attention to the sending unit sealing.  I will take my time with the sending unit, and under the circumstances, do a "bench" setup on all the seals


If I were to put a little pressure behind the water leak test, what would you suggest?  5lbs?  10lbs?  15lbs?

--Mark

Back To Top PM Quote Reply

 Posted: 01-29-2008 06:23 pm
  PM Quote Reply
7th Post
Greg Fletcher
Administrator


Joined: 03-11-2005
Location: Lake Nacimiento, California USA
Posts: 430
Status: 
Offline
What really alarmed me about the replacement tank issue is that weird seal they come with. I can't imagine why the builder can't improve on this. The original story in question (see previous thread) mentions that the JH owner had his mechanic do the install and the mechanic was the guy that raised the red flag on the whole seal being a bogus fix- they prefer I not mention the mechanics name, but he is a well known expert with a highly respected shop and and has decades of racing experience. I would be concerned if I owned one of these tanks and I would certainly take the time to complete a correct repair as Erik has done.

As far a replacements go- you can't beat Renew Tank Repair that these guys do < http://www.gas-tank.com/>. This is very high quality, permanent repair that will not fall apart with age.

Back To Top PM Quote Reply  

 Posted: 01-29-2008 07:04 pm
  PM Quote Reply
8th Post
mdutch
Member


Joined: 03-12-2005
Location: Dallas, Texas USA
Posts: 74
Status: 
Offline
Harkes wrote: I could try and make a picture of the seal if interested? Indeed the aluminium is a little soft, so one has to be careful when tightening the locking ring.
[snip]
Good luck
erik

I'd really like a photo and/or description of what you came up with, as I will be dealing with this next month.  If you have a photo, or sketch with dimensions and a description of the materials used, I'd be very grateful.

Greg, I agree this "build" is a disappointment.  However, unless I'm mis-reading things, it seems the only big issue here is the sending unit area.  I will do a water test (no pressure) to check the welds this weekend, and see how my welds are.

Again, os there any value in pressure testing the tank and if so, at what PSI?  I thought as a 70s car it would be vented through the cannister, so no pressure build-up would occur.  Any pressure build up I would think would be nominal, but I defer to those more experienced for guidance!

Last edited on 01-29-2008 07:04 pm by mdutch

Back To Top PM Quote Reply

 Posted: 02-11-2008 02:56 pm
  PM Quote Reply
9th Post
James Wilson
Member


Joined: 11-01-2006
Location: Glasgow, Scotland, United Kingdom
Posts: 34
Status: 
Offline
After contemplating buying a replacement for mega-bucks (£450 + shipping + 17.5% VAT ~ $1100!) I decided to have the old one repaired with a new bottom welded in. I used a local radiator shop and it cost 1/5 of the replacement tank's cost.

Its been pressure tested and guaranteed. I've painted it with POR15 and will mount it with a bit of clearance underneath, so it should be rust proof....

Back To Top PM Quote Reply  

 Posted: 02-12-2008 03:45 pm
  PM Quote Reply
10th Post
mdutch
Member


Joined: 03-12-2005
Location: Dallas, Texas USA
Posts: 74
Status: 
Offline
mdutch wrote: If I were to put a little pressure behind the water leak test, what would you suggest?  5lbs?  10lbs?  15lbs?

--Mark
Repeating myself, because I have no answer yet and really don't know if there's any value in pressure testing a fuel tank which theoretically should not have pressure in it...

If I were to put a little pressure behind the water leak test, what would you suggest?  5lbs?  10lbs?  15lbs?
Any advice guesses out there?  I really have no idea what's appropriate here.

Back To Top PM Quote Reply

 Posted: 02-12-2008 04:25 pm
  PM Quote Reply
11th Post
Greg Fletcher
Administrator


Joined: 03-11-2005
Location: Lake Nacimiento, California USA
Posts: 430
Status: 
Offline
Try 10 lbs and you'll see what it can handle.

Back To Top PM Quote Reply  

 Posted: 02-13-2008 01:55 am
  PM Quote Reply
12th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
When we pressure test plumbing pipes we use 4psi. Believe me, when a cap blows off there is a loud pop!

Water cannot travel in the tiny crevices where solvent can. I would start with about 2psi and use a spray bottle of soapy water if it doesn't hold pressure. When the tank starts bulging you'll know it's enough pressure.

Kurt

Back To Top PM Quote Reply

 Posted: 02-13-2008 04:19 pm
  PM Quote Reply
13th Post
mdutch
Member


Joined: 03-12-2005
Location: Dallas, Texas USA
Posts: 74
Status: 
Offline
Thanks for the feedback. 

I didn't want to over-pressurize it since a fuel tank is not supposed to carry internal pressure, and I had received a message suggesting 20lbs.  That seemed excessive.  I mean really, it's a gas tank, not a radiator.  I'm not trying to pop dents or split seams here!

Back To Top PM Quote Reply  

 Posted: 01-08-2009 11:34 pm
  PM Quote Reply
14th Post
roverman
Member
 

Joined: 11-07-2008
Location:  
Posts: 85
Status: 
Offline
Hello all, I'm considering purchase of "TANKS INC" p.n.# U3-g , factory galvanized steel , universal fit gas tank for use in Healy/later and MGB. roadster/now. They seem to be knowledgeble/reputable- a good combination. I bought a 55-57 Chevy Stainless tank from them. It appears flawless. Not tested yet. I suggest logging into their webbsite regarding this and other tanks. I havent yet discussed if they can/would move "filler" to center. Standard cost is $250.00. Stainless not listed but if there is enough interest?   Fuel for thought, roverman.

Back To Top PM Quote Reply

 Posted: 01-08-2009 11:40 pm
  PM Quote Reply
15th Post
JodyFKerr
Member


Joined: 02-21-2008
Location: Tempe, Arizona USA
Posts: 48
Status: 
Offline
There's a fllow named Gorge out in california that makes aluminum gas tanks for the JH. I think min cost me $350.00. It's rally pretty, shiny and lighter than heck.

Back To Top PM Quote Reply  

 Posted: 01-09-2009 12:46 am
  PM Quote Reply
16th Post
roverman
Member
 

Joined: 11-07-2008
Location:  
Posts: 85
Status: 
Offline
Thanks for the response, but I typed in "George of California" to scource the tank on Internet.... it didn't work. roverman

Back To Top PM Quote Reply

 Posted: 01-09-2009 11:24 pm
  PM Quote Reply
17th Post
Art DeKneef
Member
 

Joined: 03-12-2005
Location: Mesa, Arizona USA
Posts: 340
Status: 
Offline
His name is Jorge. Check the previous posts about the tanks.

He also has a JH tank on eBay right now that ends in a day.

Art

Back To Top PM Quote Reply  

 Posted: 01-10-2009 12:13 am
  PM Quote Reply
18th Post
roverman
Member
 

Joined: 11-07-2008
Location:  
Posts: 85
Status: 
Offline
Thanks Art. I sent my questions about e-bay tank to "angelheartpancho" regarding problems and guarrantee, heehee. I hope he has one. Art/roverman.

Back To Top PM Quote Reply

 Posted: 01-13-2009 01:21 am
  PM Quote Reply
19th Post
roverman
Member
 

Joined: 11-07-2008
Location:  
Posts: 85
Status: 
Offline
Hello, Well I'm hoping this isn't the same guy/mfg'r. as described in previous post with inherent design/material and attitude problems. I intend to inspect said tank at point of purchase. I'll be looking for problem areas.  Anyone out there know what standard fuel pick-up I.D. in inches is? Any suggestions? Thanks, roverman.

Back To Top PM Quote Reply  

 Posted: 01-13-2009 01:23 am
  PM Quote Reply
20th Post
roverman
Member
 

Joined: 11-07-2008
Location:  
Posts: 85
Status: 
Offline
Same Jorge as on e-bay ad now? roverman.

Back To Top PM Quote Reply

Current time is 05:35 pm Page:    1  2  Next Page Last Page    
> Jensen Healey & Jensen GT Tech > Fuel Stuff > Tanks, you're welcome Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems