Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Seat recovering  Rating:  Rating
AuthorPost
 Posted: 04-20-2006 04:25 am
  PM Quote Reply
1st Post
edward_davis
Member


Joined: 07-06-2005
Location: Eugene, Oregon USA
Posts: 162
Status: 
Offline
Two quick questions:  I've heard that the club magazine did a series on installing the Delta seat covers a while back.  When was that, and can I get a copy of that series? (it's from before I joined)

Also, is there a trick to getting the seats out of the car?

Thanks so much.

Edward

Back To Top PM Quote Reply  

 Posted: 04-20-2006 04:44 am
  PM Quote Reply
2nd Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline
I think the seat cover replacement article may be found in one of the online back issues in the 'club garage'.  I have a vague recollection of having seen the article, but have no idea what issue it might have been in.

Each seat is held to its rails with four nuts and bolts that are almost impossible to access, and each rail is held to the transverse seat support brackets with two large allen screws (total of four per seat).  In my car, I could only undo each allen screw a sixth of a turn at a time, and consequently their removal took literal hours.  It's as severe a test of one's patience as I've come across recently. 

Rust is often present, and the use of penetrating oil -- or a cutting torch -- is likely to be mandatory.  Generous amounts of anti-sieze compound on all the hardware will be of benefit for any future removal that becomes necessary.

An alternative, which may not be possible when the seat is in place, is to pop off the ten C-clips that hold the bottom cushion to the seat frame, then lift the cushion up and out.  This allows direct access to all the hardware.  IIRC, there are normally two clips holding the vinyl to the seat frame's front tube, two holding the vinyl to the rear, and three on either side.

It's been my experience that the bottom seat cushions stay in place reasonably well without any C-clips at all.  Unfortunately, doing so may leave the cushions subject to removal by random passers-by.

Edit: The bottom cushions attach with C-clips to the seat frame, not the floor as originally stated.  The text above has been corrected.

Last edited on 04-23-2006 04:30 am by Mark Rosenbaum

Back To Top PM Quote Reply

 Posted: 04-20-2006 07:57 pm
  PM Quote Reply
3rd Post
Greg Fletcher
Administrator


Joined: 03-11-2005
Location: Lake Nacimiento, California USA
Posts: 430
Status: 
Offline
I don't remember either that article. I had some issues with the Delta seat covers and had to return them when I did that on my last car some years ago. I can only assume those problems have been worked now, but I have not seen a set done and installed recently.

Just my opinion, but if you want the seats to look sharp- skip the DIY and find a good auto upholsterer. What they do really is a skill that isn't normally matched by a home restorer and you will see it in the finished product.

Back To Top PM Quote Reply  

 Posted: 04-23-2006 04:00 am
  PM Quote Reply
4th Post
Mike Aubuchon
Member
 

Joined: 03-13-2005
Location: Surprise, Arizona USA
Posts: 20
Status: 
Offline
I have to agree with Greg. A professional upholstery job is hard to beat. It also gives you a lot of options to customize your interior. I rebuilt my interior in 2000 using a charcoal gray cloth for the seats and door panels. The center panels in the seats are a gray with a small pattern in it. I had vertical stiching added on the door panels from the window down to the horizontal trim strip and spaced about an inch and a half apart. This really broke up the flat look of the doors. Using cloth made the driving much more comfortable. No more sticking to the seats in warm weather. I figured this interior is going to be in the car for a long time so it was worth the extra expence to have it done. 

 Good luck with your project.

Back To Top PM Quote Reply

 Posted: 04-24-2006 01:02 am
  PM Quote Reply
5th Post
LambandAndy
Member


Joined: 10-21-2005
Location: Eastanollee, Georgia USA
Posts: 72
Status: 
Offline
A trick I used to remove the pesky allen heads holding down the seat rails was to cut a 1/4" allen wrench off about an 1-1/4" long and insert it into the screw (so that a 1/4" or so protrudes above the rail), then turn it with a regular 1/4" open end wrench.  A 1/4" ratchet wrench would work even better if you can find one.

Andy

#15223

Back To Top PM Quote Reply  

 Posted: 04-24-2006 02:56 am
  PM Quote Reply
6th Post
Arvin Appelman
Member
 

Joined: 03-14-2005
Location: Columbia, Tennessee USA
Posts: 50
Status: 
Offline
I bought a set of covers for seats and door panels from Delta 3 years ago.  Putting the covers on was the easy part.  I had one with a borken frame and the straps were stretched to the limit on both.  The Delta parts fit well and and look original.  If you order from Delta, don't forget the headrest rings.

If I had to do it over, I think I would look for a more comfortable replacement.  I have done some measuring and I think mid 90's Saturn seats would fit nicely.

Back To Top PM Quote Reply

 Posted: 05-01-2006 05:59 pm
  PM Quote Reply
7th Post
Jay
Member


Joined: 08-05-2005
Location: Canton, Ohio USA
Posts: 73
Status: 
Offline
Does anyone have any ideas on how to remove the seat mounting screws when the blind nut in the body rail does not appear to be held from rotating? I'm a little reluctant to use a cutting torch on this to gain access. I was looking for a clever idea.

Back To Top PM Quote Reply  

 Posted: 05-01-2006 08:27 pm
  PM Quote Reply
8th Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline
Try holding the nut in place with the shaft of a screwdriver or something similar.  It might be necessary to drill a hole into the floor bracket to do this.  If that doesn't work, you can try pulling off the C-clips holding the seat bottom cushion in place, removing the cushion, and working from above.  And if that doesn't work, you may need to use the torch.

Back To Top PM Quote Reply

 Posted: 04-21-2008 02:48 am
  PM Quote Reply
9th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Mine are 7/32" allen heads.

Back To Top PM Quote Reply  

 Posted: 04-27-2008 08:15 pm
  PM Quote Reply
10th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
OK, got the seats out and the cover off in preparing to replace the seat foam with Delta's replacements. However, the elastic support bands are no longer tight or very elastic. Does anyone have an idea for repair or replacement. Will try this week to get the seat frame to an upholsterer for advice, but the locals are either 8 to 10 weeks behind or recovering from surgery.

Back To Top PM Quote Reply

 Posted: 04-27-2008 09:06 pm
  PM Quote Reply
11th Post
John Finch
Member
 

Joined: 08-01-2005
Location: Minneapolis MN
Posts: 122
Status: 
Offline
I purchased elastic strap material (for cheap) from an auto upholstery shop and my wife sewed the loop ends on her machine. I used the old straps as templates allowing for 30+ years of stretch. If you don't sew I suppose you could devise a plate/clamp/rivets etc of some sort to secure the loops.  I replaced the seat straps only and no foam. It was a big improvement. I had to guess as to the tension on the new straps. Difficult to stretch iirc during re installation but no sore butt after 3-4 hour trips so its ok. Good luck.  John

Back To Top PM Quote Reply  

 Posted: 04-27-2008 09:31 pm
  PM Quote Reply
12th Post
dwalls1
Member
 

Joined: 04-11-2008
Location: Bloomfield, New Mexico USA
Posts: 207
Status: 
Offline
Thanks John!

    I had a hunch that an upholstery shop might be able to come up with the straps. I'll check them out at the first op. The wife will be back from her visit before I can use her machine, so I may have to do the plate rivet thing, but you have been most helpful and encouraging. Thank You

Back To Top PM Quote Reply

Current time is 05:09 pm  
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Seat recovering Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems