| ||||
| ||||
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Steering wheel adaptor | Rate Topic |
| Author | Post |
|---|
| Posted: 12-20-2014 02:50 am |
|
1st Post |
|
scottsmi Member
|
Does anybody have recommendations for a wood steering wheel for my JH? I understand I need a adapter kit as well. I called delta and they are out.
|
||||||||||||||
| |||||||||||||||
| Posted: 12-21-2014 11:02 am |
|
2nd Post |
|
gmgiltd Member
|
Try Moto Lita in the UK - they are expensive but absolutely top quality I have the leather one on My GT on which the cowl shroud needed to be modified slightly they are intended for the JH. Comes with all the bits you need to install. https://www.moto-lita.co.uk/our-products/your-car/Wheel_Details.aspx?CR_ID=154&CB_ID=18&WH_ID=3 Gordon
|
|||||||||||||
| ||||||||||||||
| Posted: 01-05-2017 03:10 am |
|
3rd Post |
|
Earthscrew Member
|
I know this is an old subject, however I have wanted to change out my cracked original steering wheel but did not wish to pay the price for the adaptor, as I have already invested far more than ever anticipated in this car. After much research, I found that the Grant adapter number 3597 fits perfect. Contrary to what I have read everywhere, I can not find a single adapter for an old GM that fit my 5/8" shaft. The 3597 fits older Mazdas, and a couple Fords and cost me $24.00 at Pep Boys. I ordered a 15" wood walnut wheel from Grant off Amazon for $125.00 and it looks great to me.
|
||||||||||||||
| |||||||||||||||
| Posted: 01-07-2017 06:03 pm |
|
4th Post |
|
scottsmi Member
|
Thanks for the update. I have been wondering about how to get an adapter and have seen one on Ebay for $200!
|
|||||||||||||
| ||||||||||||||
| Posted: 01-07-2017 06:39 pm |
|
5th Post |
|
Earthscrew Member
|
Glad I could help, Grant is a much more resonable approach for a steering wheel and you can get it at any Pep Boyd. They happened to have it in stock at the Simi Valley store, but even if they need to order it, no big deal. Best regards!
|
||||||||||||||
| |||||||||||||||
| Posted: 01-07-2017 11:36 pm |
|
6th Post |
|
Frank Schwartz Member
|
Maybe you can post a picture or two???and what emblem is in the center of the "new" wheel???
|
|||||||||||||
| ||||||||||||||
| Posted: 01-07-2017 11:44 pm |
|
7th Post |
|
Earthscrew Member
|
I am happy to, but cannot figure out how to move the pictures into this blog???
|
||||||||||||||
| |||||||||||||||
| Posted: 01-07-2017 11:58 pm |
|
8th Post |
|
Earthscrew Member
|
Tried to post a picture, but I get a message telling me that the file is too big, only one photo do I do not know what is wrong. I can tell you it has no emblem, simply a plain chrome plate, actually looks quite good for an inexpensive wheel
|
|||||||||||||
| ||||||||||||||
| Posted: 01-08-2017 10:15 pm |
|
9th Post |
|
Jensen Healey Super Moderator 
|
You need to host your photos at a service like Photobucket which creates "img" tags. Then paste the tag into your post. I'm not an expert on the nuances of photo hosting, but learned to get it working from Subwoofer. Perhaps he will be so kind as to start a thread with instructions. Kurt
|
||||||||||||||
| |||||||||||||||
| Posted: 01-08-2017 11:00 pm |
|
10th Post |
|
Earthscrew Member
|
Kurt, I no so good at this either, I will turn this over to my wife as she understands a bit more! Regards
|
|||||||||||||
| ||||||||||||||
| Posted: 01-19-2017 05:23 am |
|
11th Post |
|
dbeliveau74 Member 
|
You can use an app like PIXresizer to make the pic small enough to post on this forum. You can find it by doing a search for the name and its free!! cheers, Dan
|
||||||||||||||
| |||||||||||||||
| Posted: 01-19-2017 05:26 am |
|
12th Post |
|
dbeliveau74 Member
|
Here is an example of a reduced pic of my dash and wheel. Not sure of the adapter or wheel source as it was installed by the PO. Attachment: DSC_1099 (600 x 397).jpg (Downloaded 126 times) Last edited on 02-25-2017 02:54 am by dbeliveau74 |
|||||||||||||
| ||||||||||||||
| Posted: 02-24-2017 08:17 pm |
|
13th Post |
|
allstateguy Member 
|
I too started with the 3597 adapter, but since I wanted a Nardi wheel (same as Momo bolt pattern) I flipped it over so it wouldn't travel too far down the shaft, peeled off the useless copper horn contact panel, drilled two holes for grub screws to activate the turn signal reset. Then the fun began. To get enough depth for the steering shaft I had to use a 1" Chinese adapter which had the wrong bolt pattern (Forever Sharp) and a .5" adapter which could have gone from Grant to Nardi, cut out its center and countersunk the Forever Sharp bolt pattern to take 5mm allen screws. See attached pix. Total price $24+$14+$12 all on eBay, plus a couple of bucks for screws. Now the Nardi wheel fits and everything works like it is supposed to. Horn on the left column lever was actually an advantage in this situation. Attachment: JH nardi wheel adapter front small.jpg (Downloaded 101 times) Last edited on 02-24-2017 08:17 pm by allstateguy |
||||||||||||||
| |||||||||||||||
| Posted: 02-24-2017 08:20 pm |
|
14th Post |
|
allstateguy Member
|
the side facing the column Attachment: JH nardi wheel adapter small.jpg (Downloaded 100 times)
|
|||||||||||||
| ||||||||||||||
| Posted: 02-24-2017 08:20 pm |
|
15th Post |
|
allstateguy Member
|
with the wheel, but not attached yet, more work to do under the dash Attachment: wheel w adapter I made 2-23-17 small.jpg (Downloaded 102 times)
|
||||||||||||||
| |||||||||||||||
| Current time is 06:13 pm | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > Steering wheel adaptor | Top |
