| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Complete dash removal for dashpad install |
| ||||
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Complete dash removal for dashpad install |
| Moderated by: Greg Fletcher |
|
||||||||||||||
| Complete dash removal for dashpad install | Rating: 
|
| Author | Post |
|---|
| Posted: 05-21-2011 04:11 pm |
|
1st Post |
|
cavanbound Member
|
I looked through the postings and tech articles, and based on the tech article (http://www.jensenhealey.com/tech/dash/dashcap.html), I'm planning to pull my entire dash to get a proper fit and look for the dashcap I have from Delta. I've not found any references to how many mounting points I need to pull for the entire dash to come loose (also, do I need to pull all the wiring and the oil pressure connection, or is there enough play in this if the dash is simply pulled loose? Found this pic of the dash pulled from another JH (http://www.pjsmotorsports.com/?attachment_id=232), but cannot discern mounting points. I've found the twin screws at right and left of the underside dash - I'm assuming there are other mount points in the mid-section? Thanks for any pointers.
|
||||||||||||||
| |||||||||||||||
| Posted: 05-21-2011 10:35 pm |
|
2nd Post |
|
Ron Mau Member
|
In addition to the mounting points on the right and left, there are three bolts under the dash directly under the top of the dash, one on each end and one in the middle. The gauge cluster should pull out as it is a friction fit on a pin in the middle and two screws in the upper corners of the cluster, They are sometimes rusted in place. You can use a hammer and gently tap it to work it loose it so it will pull out. Put some anti seize on it before you reinstall it. The oil pressure line will have to be removed. There are two scews the attach the radio console to the dash. The gauge pod has 2 wiring connections that need to be disconnected. You might need to remove the switch panels on the bottom of the dash along with the glove box. They might come out with the dash I don't recall. I took all the dash and gauges out as I did the Madera wood at the same time. Hope this helps. It sounds like a lot of work but it doesn't take that much time to do. Ron Mau 16367 Davenport, IA
|
|||||||||||||
| ||||||||||||||
| Posted: 05-22-2011 12:59 am |
|
3rd Post |
|
cavanbound Member
|
Ron- Good advice - my Madera wood will be here in a few days as well, so I'll likely couple the two projects (dashcover/wood fascia). Thanks again - Matt
|
||||||||||||||
| |||||||||||||||
| Posted: 02-16-2012 01:45 am |
|
4th Post |
|
Besecker Member
|
Guys: Any advice on what tool to use to reach the 8mm nuts that secures the dash over the steering wheel. I'm having a hard time reaching them it to all the clutter. My little 8mm wrench worked fine on the other two. Thanks. Bob JH5
|
|||||||||||||
| ||||||||||||||
| Posted: 02-16-2012 03:10 pm |
|
5th Post |
|
JodyKerr Member 
|
IIRC, it was one or two very long socket extensions, and may have had a universal in the middle.
|
||||||||||||||
| |||||||||||||||
| Posted: 02-16-2012 06:00 pm |
|
6th Post |
|
Jim Ketcham Member
|
They are not metric. Engine metric, body SAE.
|
|||||||||||||
| ||||||||||||||
| Current time is 07:56 pm | |
| > Jensen Healey & Jensen GT Tech > Body & interior stuff > Complete dash removal for dashpad install | Top |
