Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Replacement seat belts  Rate Topic 
AuthorPost
 Posted: 06-03-2005 03:24 am
  PM Quote Reply
1st Post
Adam H
Member
 

Joined: 03-12-2005
Location: Poughkeepsie, New York USA
Posts: 6
Status: 
Offline
I bought replacement seat belts from Wescoperformance.com.  A little expensive $74.90 each plus shipping but they fit like original equipment.

I took off the latch and put on the Jensen shoulder belt turn around piece. 

Order the WELR-N for roadsters.http://www.westcoperformance.com

Back To Top PM Quote Reply  

 Posted: 06-03-2005 01:22 pm
  PM Quote Reply
2nd Post
Brian Kelly
Member
 

Joined: 03-22-2005
Location:  
Posts: 43
Status: 
Offline
Thanks for the link Adam,

You've got to take the "t" out to get to the right site

http://www.wescoperformance.com

Replacing the seat belts is on my list of "to do's".

I wonder how these compare with the more expensive ones that Delta sells?

Any one care to comment?

Brian.

Back To Top PM Quote Reply

 Posted: 06-03-2005 07:33 pm
  PM Quote Reply
3rd Post
George
Member
 

Joined: 04-05-2005
Location: Boyds, Maryland USA
Posts: 88
Status: 
Offline
I seem to remember something in a newsletter about just replacing the webbing for a really low cost?  Anybody know about that?

Back To Top PM Quote Reply  

 Posted: 06-28-2005 06:34 pm
  PM Quote Reply
4th Post
kneff
Member
 

Joined: 04-06-2005
Location: San Jose, California USA
Posts: 21
Status: 
Offline
I'm pretty sure my original seat belts are no longer of any use. I don't think that the belts will lock under any condition.

What I want to save from the original belts are the two parts of the latch. That is, the female part attached to the transmission tunnel and the male part that latches into it. The female part has the "H" on it, and the male part matches the original key in style, so I'd like to retain them.

With the replacement belts, did I understand correctly that you were able to retain these parts from the original?


Thanks,
Ken

Back To Top PM Quote Reply

 Posted: 06-29-2005 02:21 am
  PM Quote Reply
5th Post
Mark Rosenbaum
Member


Joined: 03-12-2005
Location: Kingman, Arizona USA
Posts: 532
Status: 
Offline

Apparently it's getting difficult to find firms that will re-web seat belts, presumably because of liability issues. I found two sources in the SOL 'Monster List' that apparently still do this. I have neither previously heard of, nor done business with, either firm.

Arise (formerly Old Bijou Productions)
2546 Boren Drive San Jose, CA 95121
(408) 993-8225
Entry Date: 2003/12/15

Ssnake - Oyl Products, Inc
Rt 2 Box 269-6 Hawkins, Texas 75765
(903) 769-4555
(800) 284-7777
Entry Date: 1998/Dec/1

Back To Top PM Quote Reply  

 Posted: 06-30-2005 12:11 pm
  PM Quote Reply
6th Post
Adam H
Member
 

Joined: 03-12-2005
Location: Poughkeepsie, New York USA
Posts: 6
Status: 
Offline
You understood correctly.  You can use the old hardware and the new belt and retractor.  Getting the new buckle off takes a little effort but it is doable.

Adam

Back To Top PM Quote Reply

 Posted: 08-25-2005 03:22 am
  PM Quote Reply
7th Post
kneff
Member
 

Joined: 04-06-2005
Location: San Jose, California USA
Posts: 21
Status: 
Offline
Adam,

Did you have to remove the belt from the reel in order to remove the new buckle and replace it with the old one? I don't see any other way to do it, but I'd like to be wrong.


Thanks,
Ken

Back To Top PM Quote Reply  

 Posted: 11-08-2006 05:20 pm
  PM Quote Reply
8th Post
Ed
Member
 

Joined: 09-18-2006
Location:  
Posts: 2
Status: 
Offline
After purchasing the Wesco Performance #WELR-N selt belts, I found they did not fit my 1973 Jensen Healey properly.  I contacted Wesco and they suggested using the #I-3207 belts at web page:

http://www.wescoperformance.com/i-3207-retractable-install.htm

 The #I-3207 belts fit perfectly.  Unlike the #WELR-N belts, these have a sash guide.  The belt retractor mounts at the bottom of the wheel well and the sash guide mounts at the top of the wheel well.  See attached photo.  When removing the original buckles on the inboard side of the bucket seats, I cut the two wires going to each buckle so the seat belt light on the dash board no longer works.

You can  use your existing mounting bolts or order Wesco's harware kit which contains new bolts, shoulder bolts, nuts, lockwashers and large washers and bracket.  Since the Jensen Healey has mounting points for the belts, the large washers, lockwashers, bracket and nuts are not used.

Ed

San Jose, CA

Attachment: selt-belt.JPG (Downloaded 145 times)

Back To Top PM Quote Reply

Current time is 07:54 am  
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Replacement seat belts Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems