Home 
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Greg Fletcher
New Topic Reply Printer Friendly
Roll Bar  Rate Topic 
AuthorPost
 Posted: 03-10-2009 06:22 pm
  PM Quote Reply
1st Post
roblanford
Member
 

Joined: 06-27-2008
Location: Anaheim SoCal, USA
Posts: 36
Status: 
Offline
Hey y'all,

Does anybody know if the Delta roll bar will fit under the factory roadster hardtop?
I asked Delta, they said yes but did not sound very confident of their answer.
Thanks,
Robert

Back To Top PM Quote Reply  

 Posted: 03-10-2009 08:45 pm
  PM Quote Reply
2nd Post
Jensenman
Member
 

Joined: 04-14-2005
Location: Columbia, South Carolina USA
Posts: 156
Status: 
Offline
I have both a factory and an aftermarket hardtop, my Delta bar fits fine under both with about 1/2" to spare.

Back To Top PM Quote Reply

 Posted: 03-11-2009 04:48 am
  PM Quote Reply
3rd Post
roblanford
Member
 

Joined: 06-27-2008
Location: Anaheim SoCal, USA
Posts: 36
Status: 
Offline
Thanks again J'man

Back To Top PM Quote Reply  

 Posted: 03-15-2009 08:49 pm
  PM Quote Reply
4th Post
roblanford
Member
 

Joined: 06-27-2008
Location: Anaheim SoCal, USA
Posts: 36
Status: 
Offline
I am getting ready to install the Delta rollbar. Any suggestions or advice on what to look out for?

Thanks
Robert

Back To Top PM Quote Reply

 Posted: 03-16-2009 04:04 am
  PM Quote Reply
5th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
Center the bar carefully. Look uner the parcel shelf and locate the triangular gussets. Try to miss them when drilling.

The rear mounts should be tight to the rear wall as possible.

Never use the roll bar when rolling the car, it's only good for one use. Try to flip in mid air and land on the wheels.

Kurt

Back To Top PM Quote Reply  

 Posted: 03-16-2009 04:07 am
  PM Quote Reply
6th Post
Jensenman
Member
 

Joined: 04-14-2005
Location: Columbia, South Carolina USA
Posts: 156
Status: 
Offline
When drilling holes, watch CAREFULLY for brake and fuel lines! They run very close to where the left (drivers') rear mounting goes. I used a couple of pieces of 1x3 wood to hold the lines away from the underside of the car before drilling holes.

There is also a 'box' crossmember under the front of the 'deck' (parcel shelf), if you put the bar too far forward the front holes will be inside this box meaning you can't put nuts on them. Measure thrice, drill once!

Back To Top PM Quote Reply

 Posted: 03-16-2009 11:36 pm
  PM Quote Reply
7th Post
Mike Aubuchon
Member
 

Joined: 03-13-2005
Location: Surprise, Arizona USA
Posts: 20
Status: 
Offline
Hey Kurt, great answer on flipping the car. Why waste a perfectly good roll bar. As always, thanks for the great and helpful information.

Back To Top PM Quote Reply  

 Posted: 03-17-2009 07:45 am
  PM Quote Reply
8th Post
roblanford
Member
 

Joined: 06-27-2008
Location: Anaheim SoCal, USA
Posts: 36
Status: 
Offline
I'm going to send the roll bar back to delta.  I might as well spend the money on beer instead.

Back To Top PM Quote Reply

 Posted: 03-17-2009 03:16 pm
  PM Quote Reply
9th Post
Jensen Healey
Super Moderator


Joined: 03-11-2005
Location: San Anselmo, California USA
Posts: 983
Status: 
Offline
Your safety is important. Bolt that thing in there.

I know a guy who was in a massive crash in an MGB. He lost an eye but still enjoys life due to the roll bar. He said to get some padding because his head really hurt where it impacted the bar.

Where do you live Rob? I'll come over (with beer) and help you install it.

Kurt

Back To Top PM Quote Reply  

 Posted: 03-17-2009 04:42 pm
  PM Quote Reply
10th Post
roblanford
Member
 

Joined: 06-27-2008
Location: Anaheim SoCal, USA
Posts: 36
Status: 
Offline
Just joking about sending it back. After seeing several squashed windscreens the rollbar is mandatory. Thanks for the offer Kurt. I am in Anaheim, long way from you. I'll have it done tonight. Now if I could just find that stock aircleaner for the smog test.....

Back To Top PM Quote Reply

Current time is 05:19 pm  
> Jensen Healey & Jensen GT Tech > Body & interior stuff > Roll Bar Top




UltraBB 1.172 Copyright © 2007-2011 Data 1 Systems